bifold guide motor bracket 487
bifold knife 521
bifold knife and tamper assembly 517
bifold knife plates 520
bifold knife primary drive gears 516
bifold knife secondary drive gears 521
bifold lower roller 509
bifold roller drive gears 522
bifold roller gears 471
bifold roller springs 480
bifold upper roller 506
booklet gate jam access door 340
booklet maker aligner 498
booklet maker aligner assembly 496
booklet maker aligner belt 500
booklet maker aligner front paper guide 493
booklet maker aligner gears 501
booklet maker aligner jam access door 460
booklet maker aligner middle paper guide 499
booklet maker aligner rear paper guide 494
booklet maker aligner solenoid 501
booklet maker controller board 462
booklet maker controller board holder 462
booklet maker decurl gears 483
booklet maker decurl guide 485
booklet maker decurl lever 468
booklet maker exit roller springs 455
booklet maker front cover 456
booklet maker jam access door 465
booklet maker lower paddle 456
booklet maker paddle belt 474
booklet maker paddle gears 475
booklet maker right cover 457
booklet maker staple unit 510
booklet maker support 457
booklet maker tamper tray 527
booklet maker transport belt 481
booklet maker transport gear 481
booklet maker transport idler rollers 467
booklet maker transport paper guide assembly 466
booklet maker transport paper guide lever 469
booklet maker transport roller 482
booklet maker trifold rollers 472
booklet maker upper paddle 504
exit motor bracket 277
HPBF bin and lower left cover 344
HPBF bin bail 333
HPBF elevator bin full sensor actuator 347
HPBF exit roller cover 347
HPT belts and gears 329
HPT cable 325
HPT door 324
HPT door hinges 326
HPT door locks 321
HPT feed sensor actuator 323
HPT holding bracket 322
HPT inner paper guide 321
HPT rear cover 325
HPT right top cover 324
HPT transport rollers 329
middle frame brace 464
motor (bifold guide) 486
motor (bifold knife) 491
motor (bifold roller) 471
motor (booklet maker aligner) 491
motor (booklet maker decurl) 479
motor (booklet maker paddle) 476
motor (booklet maker tamper) 492
motor (booklet maker transport) 478
motor (HPT transport) 327
motor (SHPF aligner) 391
motor (SHPF compiler eject) 399
motor (SHPF compiler feed roller release) 388
motor (SHPF compiler pre-eject) 400
motor (SHPF elevator bin stack height) 353
motor (SHPF elevator) 359
motor (SHPF feed) 356
motor (SHPF front tamper) 354
motor (SHPF paddle) 384
motor (SHPF rear tamper) 357
motor (SHPF staple unit carriage) 371
motor (SHPF transport) 356
motor (staple finisher aligner) 254
motor (staple finisher elevator) 250
motor (staple finisher exit) 253
motor (staple finisher staple unit carriage) 263
motor (staple finisher tamper) 238
motor (staple finisher transport) 247
motor (staple finisher upper exit) 251
motor (trifold guide) 489
punch unit 365
sensor (bifold guide home) 488
sensor (bifold knife home) 519
sensor (booklet maker aligner home) 495
sensor (booklet maker decurl) 484
sensor (booklet maker fold exit) 515
sensor (booklet maker paddle home) 477
sensor (booklet maker tamper home) 530
sensor (booklet maker transport) 467
sensor (HPBF bin empty, receive) 347
sensor (HPBF bin empty, transmit) 347
sensor (HPBF elevator bin full) 347
sensor (HPT door) 323
sensor (HPT feed) 322
4021, 7421
Index
686
To Next Page
Loading...
