Parameters
Connector/Binector (BICO)-Parameters
1-428
© Siemens AG 2009 All Rights Reserved
SINAMICS G120 Control Units CU230P-2 Parameter Manual (LH9), 11/2009
r1809 CO: Modulator mode actual / Modulator mode act
r2050[0...7] CO: PROFIBUS PZD receive word / PZD recv word
r2089[0...4] CO: Send binector-connector converter status word / Bin/con ZSW send
r2120 CO: Sum of fault and alarm buffer changes / Sum buffer changed
r2121 CO: Counter, alarm buffer changes / Alrm buff changed
r2131 CO: Actual fault code / Actual fault code
r2132 CO: Actual alarm code / Actual alarm code
r2169 CO: Actual speed smoothed signals / n_act smth message
p2201[0...n] CO: Technology controller, fixed value 1 / Tec_ctrl fix val 1
p2202[0...n] CO: Technology controller, fixed value 2 / Tec_ctrl fix val 2
p2203[0...n] CO: Technology controller, fixed value 3 / Tec_ctrl fix val 3
p2204[0...n] CO: Technology controller, fixed value 4 / Tec_ctrl fix val 4
p2205[0...n] CO: Technology controller, fixed value 5 / Tec_ctrl fix val 5
p2206[0...n] CO: Technology controller, fixed value 6 / Tec_ctrl fix val 6
p2207[0...n] CO: Technology controller, fixed value 7 / Tec_ctrl fix val 7
p2208[0...n] CO: Technology controller, fixed value 8 / Tec_ctrl fix val 8
p2209[0...n] CO: Technology controller, fixed value 9 / Tec_ctrl fix val 9
p2210[0...n] CO: Technology controller, fixed value 10 / Tec_ctrl fix val10
p2211[0...n] CO: Technology controller, fixed value 11 / Tec_ctrl fix val11
p2212[0...n] CO: Technology controller, fixed value 12 / Tec_ctrl fix val12
p2213[0...n] CO: Technology controller, fixed value 13 / Tec_ctrl fix val13
p2214[0...n] CO: Technology controller, fixed value 14 / Tec_ctrl fix val14
p2215[0...n] CO: Technology controller, fixed value 15 / Tec_ctrl fix val15
r2224 CO: Technology controller, fixed value effective / Tec_ctr FixVal eff
r2245 CO: Technology controller mot. potentiometer setpoint before RFG / Tec_ctr mop befRFG
r2250 CO: Technology controller motorized potentiometer setpoint after RFG / Tec_ctr mop aftRFG
r2260 CO: Technology controller setpoint after ramp-function generator / Tec_ctr set aftRFG
r2262 CO: Technology controller setpoint after filter / Tec_ctr set aftFlt
r2266 CO: Technology controller actual value after filter / Tec_ctr act aftFlt
r2272 CO: Technology controller actual value scaled / Tech_ctrl act scal
r2273 CO: Technology controller error / Tec_ctrl error
p2291 CO: Technology controller maximum limiting / Tec_ctrl max_limit
p2292 CO: Technology controller minimum limiting / Tec_ctrl min_lim
r2294 CO: Technology controller output signal / Tec_ctrl outp_sig
p2295 CO: Technology controller output scaling / Tec_ctrl outp scal
r2344 CO: Technology controller last speed setpoint (smoothed) / Tec_ctrl n_setp_sm
r2397[0...1] CO: Hibernation output speed actual / Hib n_outp act
p2900[0...n] CO: Fixed value 1 [%] / Fixed value 1 [%]
p2901[0...n] CO: Fixed value 2 [%] / Fixed value 2 [%]
r2902[0...14] CO: Fixed values [%] / Fixed values [%]
p2930[0...n] CO: Fixed value M [Nm] / Fixed value M [Nm]
r3131 CO: Current fault value / Current flt value
r8784 CO: CAN status word / Status word
r11060 CO: Free tec_ctrl 0 setpoint after ramp-function generator / Ftec0 setp aft RFG
r11072 CO: Free tec_ctrl 0 actual value after limiter / Ftec0 act v af lim
r11073 CO: Free tec_ctrl 0 system deviation / Ftec0 sys dev
p11091 CO: Free tec_ctrl 0 limit maximum / Ftec0 lim max
p11092 CO: Free tec_ctrl 0 limit minimum / Ftec0 lim min
r11094 CO: Free tec_ctrl 0 output signal / Ftec0 out_sig
r11160 CO: Free tec_ctrl 1 setpoint after ramp-function generator / Ftec1 setp aft RFG
r11172 CO: Free tec_ctrl 1 actual value after limiter / Ftec1 act v af lim
r11173 CO: Free tec_ctrl 1 system deviation / Ftec1 sys dev
p11191 CO: Free tec_ctrl 1 limit maximum / Ftec1 lim max
To Next Page
Loading...
Need help?
General
