Siemens SINUMERIK Series

Index
Extended Functions
948 Function Manual, 03/2013, 6FC5397-1BP40-3BA1
Handwheel 1 active as contour handwheel, 876
Handwheel 2 active as contour handwheel, 876
Han
dwheel 3 active as contour handwheel, 876
Han
dwheel active (1 to 3), 881
Han
dwheel active (1 to 3) for geometry axis, 871
Han
dwheel direction of rotation inversion active
(geometry axis 1, 2, 3), 870
Han
dwheel direction of rotation inversion active for
contour handwheel, 876
Han
dwheel direction of rotation inversion for
geometry axis (1, 2, 3), 865
Han
dwheel direction of rotation inversion for
orientation axis (1, 2, 3),
Handwheel override active, 881
Invert h
andwheel direction of rotation (machine
axes), 879
Invert h
andwheel direction of rotation active
(machine axes), 884
Invert h
andwheel direction of rotation for contour
handwheel, 875
J
OG - Approaching fixed point 0/1/2, 880
JOG
- Approaching fixed point active, 884
JOG
- Approaching fixed point reached, 884
Machi
ne function continuous for geometry axis (1,
2, 3), 864
Machi
ne function for geometry axis (1, 2, 3), 870
Mac
hine function INC1, INC10, INC100, INC1000,
INC10000, INCvar, 879
Plus and mi
nus traverse keys, 878
Plus and mi
nus traversing command, 882
Plus and mi
nus traversing command (for orientation
axis), 872
Plus and mi
nus traversing commands (for geometry
axis), 869
Plus and mi
nus traversing keys for geometry axis
(1, 2, 3), 863
Plus and mi
nus traversing request, 882
Plus and mi
nus traversing request (for geometry
axis), 871
Plus and mi
nus traversing request (for orientation
axis), 871
Rapi
d traverse override, 877
Rapi
d traverse override for geometry axis (1, 2,
3), 862
Tra
versing key disable for geometry axis (1, 2,
3), 862
T
raversing key lock, 877
Interpolatio
n
Linear, 606
non-li
near, 607
with G0, 606
Interpolatio
n functions, 636
Interpolatio
n point, 236
Interpolato
r
path, 606
Shaft, 606
IPOBRKA, 618
IPOENDA, 618
IS feedrate st
op / spindle stop, 718
J
JOG, 392
Approaching a fixed point, 183
jog mode, 152
J
OG retract, 190
L
Language command
SPN, 576
SPP, 575
Lang
uage commands, 562
LEC, 238
Linked tran
sformation
Example, 389
Logi
cal start address, 54
Longitu
dinal grooves, 348
LS (leadi
ng spindle) active, 905
M
Machine axis (for handwheel 1, 2 or 3), 860
Machine axis identifier, 268
Manual
stroke initiation, 893
Manual travel
, 209
MC
P switchover disable, 853
MD10
010, 307
MD10
050, 83
MD10
061, 84
MD10
070, 84
MD10
071:, 84
MD10
088, 300
MD10
185, 84
MD10
200, 296
MD10
210, 697
MD10
260, 544
MD10
270, 776
MD10
300, 28
MD10
310, 28
MD10
320, 38
MD10
330, 42
MD10
350, 35