R9 Control System User Guide v5.5
Figure B.37. Measure Item........................................................................................................................ 101
Figure B.38. Property Panel Configuration ............................................................................................... 102
Figure B.39. External Hardware Devices - Preamps ................................................................................ 102
Figure B.40. External Control Support for FEMTO Preamps .................................................................... 103
Figure B.41. PMC100 ................................................................................................................................ 104
Figure B.42. PPC200 ................................................................................................................................ 105
Figure B.43. A –Z Scan Added to the Piezo Tube Item ............................................................................ 105
Figure B.44. External Hardware Item for AFM Cantilevers ....................................................................... 105
Figure B.45. Microscopes ......................................................................................................................... 106
Figure B.46. Piezo Sensitivity Selector ..................................................................................................... 106
Figure B.47. Show/Hide Items from Hardware Composites ..................................................................... 107
Figure C.1. RHK STM Beetle - Connections Block Diagram .................................................................... 108
Figure C.2. R9 Connection Diagram for the RHK UHV300 Beetle STM .................................................. 108
Figure C.3. Combined Bias and Preamp Cable ........................................................................................ 109
Figure C.4. RHK AFM/STM Beetle - Connections Block Diagram ........................................................... 110
Figure C.5. RHK STM Pan - Connections Block Diagram ........................................................................ 111
Figure C.6. Combined Bias and Preamp Cable ........................................................................................ 112
Figure D.1. R9 Preamp I/O 44-Pin Female Connector ............................................................................. 114
Figure D.2. DC Power Output 9-Pin Female Connector ........................................................................... 115
Figure D.3. R9 Laser I/O 26-Pin Female Connector ................................................................................. 116
Figure D.4. R9 High Voltage Output 10-Pin Female Connector ............................................................... 117
Figure D.5. R9 High Voltage Output Defaults for RHK Microscopes ........................................................ 117
Figure D.6. R9 Rear Panel BNCs ............................................................................................................. 118
Figure D.7. R9 Low Voltage Outputs 15-Pin Female Connector .............................................................. 119
Figure D.8. R9 Digital I/O 25-Pin Connectors ........................................................................................... 120
Figure D.9. R9 Preamp I/O Cable 44-pin to 15-pin ................................................................................... 121
Figure E.1. Common Scan Head Designs ................................................................................................ 122
Figure E.2. RHK UHV300/700 High Voltage Block ................................................................................... 123
Figure E.3. RHK UHV350/750 High Voltage Block ................................................................................... 123
Figure E.4. RHK UHV900 High Voltage Block .......................................................................................... 124
Figure F.1. The Approach Procedure Panel ............................................................................................. 126
Figure F.2. STM Beetle Approach Procedure Panel ................................................................................ 127
Figure F.3. AFM/STM Beetle Approach Procedure Panel ........................................................................ 128
Figure F.4. Beetle Single Step In Procedure ............................................................................................ 129
Figure F.5. Beetle Slow Approach Procedure ........................................................................................... 130
Figure I.1. RHK UHV300 STM IHL ........................................................................................................... 135
Figure I.2. Scan Processor Connection to High Voltage Block................................................................. 136
Figure I.3. Setting Gain in Feedback Mode .............................................................................................. 138
Figure I.4. Hardware Watcher in PLL ........................................................................................................ 140
Figure I.5. Fast Sweep Abort .................................................................................................................... 141
Figure I.6. Settings for Fast Sweep Abort ................................................................................................. 141
Figure I.7. 'Yes/No' Message Box ............................................................................................................. 142
Figure I.8. Play a Sound with Message Box Notification .......................................................................... 143
Figure I.9. Simplified R9 Controls ............................................................................................................. 144
Figure J.1. Creating a Procedure .............................................................................................................. 145
Figure J.2. New Procedure Space ............................................................................................................ 146
Figure J.3. Connecting Components in Hardware Space and Procedure Space ..................................... 147
Figure J.4. Selecting a Wire ...................................................................................................................... 148
Figure J.5. Using the Arranging Pins ........................................................................................................ 148
Figure J.6. Deleting a Wire........................................................................................................................ 149
Figure J.7. Pulse Tip template .................................................................................................................. 149
Figure J.8. Pulse Tip - set first Activate to CH1 Drive ............................................................................... 149
Figure J.9. Pulse Tip - CH1 Drive Properties ............................................................................................ 150
Figure J.10. Pulse Tip - Hiding CH1 Drive Properties .............................................................................. 151
Figure J.11. Pulse Tip - Setting the CH1 Drive Pulse Rise ....................................................................... 152
Figure J.12. Pulse Tip - Setting the Pulse Duration .................................................................................. 152
To Next Page
Loading...