RHK Technology R9 - Page 8

viii
List of Figures
Figure 1.1. Check the R9 for damage ........................................................................................................... 1
Figure 1.2. Location of Power, Frequency, Voltage and Serial Number Information ................................... 2
Figure 1.3. Ethernet Connection Diagram .................................................................................................... 3
Figure 1.4. R9 Dashboard ............................................................................................................................. 4
Figure 1.5. Opening a preconfigured IHDL™ ............................................................................................... 6
Figure 1.6. Selecting the Workbench tab ...................................................................................................... 6
Figure 1.7. RHK UHV300 Preconfigured STM Hardware Workbench.......................................................... 7
Figure 1.8. UHV 300 STM Hardware Workbench Overview ......................................................................... 8
Figure 1.9. Hardware Space ....................................................................................................................... 10
Figure 1.10. Save the IHDL with a New Name ........................................................................................... 12
Figure 1.11. Auto-backup IHDL Files .......................................................................................................... 12
Figure 1.12. Workbench - Testing UHV 300.ihl .......................................................................................... 13
Figure 1.13. R9s Testing Screen using the Testing UHV 300 ihl ............................................................... 14
Figure 1.14. Oscilloscope - Topography and Current ................................................................................. 16
Figure 1.15. Testing the Input Offset .......................................................................................................... 17
Figure 1.16. Spectrum Analyzer Result at Full Bandwidth ......................................................................... 18
Figure 1.17. Spectrum Analyzer Result with 2 kHz Filter with 48 dB rolloff ................................................ 19
Figure 1.18. Bias Voltage and CH1 Drive Settings ..................................................................................... 20
Figure 1.19. Bias Modulation through the Tunneling Gap Simulator .......................................................... 21
Figure 3.1. Open the Approach Procedures Panel ..................................................................................... 25
Figure 3.2. Typical Dashboard for STM ...................................................................................................... 26
Figure 3.3. Camera View of the Tip and Sample ........................................................................................ 27
Figure 3.4. Z Feedback Bar ........................................................................................................................ 29
Figure 3.5. Mode Switching......................................................................................................................... 29
Figure 4.1. Checking the Available Signals ................................................................................................ 31
Figure 4.2. Scan Area Window Main Panel ................................................................................................ 32
Figure 4.3. Scan Area Window - Advanced, Save ...................................................................................... 34
Figure 4.4. Scan Area Window – Tip Standby Position .............................................................................. 34
Figure 4.5. Scan Area Window - Nav Config., Image Settings ................................................................... 35
Figure 4.6. Multi-height Imaging ................................................................................................................. 36
Figure 4.7. Open an Image Window ........................................................................................................... 37
Figure 4.8. Open an Image Line ................................................................................................................. 37
Figure 4.9. Scan Area Window - Drift Settings ........................................................................................... 39
Figure 4.10. Automatic Drift Correction ....................................................................................................... 40
Figure 4.11. Image+Spectroscopy - Points ................................................................................................. 42
Figure 4.12. Image+Spectroscopy - Line .................................................................................................... 42
Figure 4.13. Image+Spectroscopy - Region ............................................................................................... 43
Figure 5.1. File Explorer View ..................................................................................................................... 44
Figure 5.2. Shadow style Artifact from X Offset Subtract ........................................................................... 45
Figure 5.3. Image Manipulation .................................................................................................................. 46
Figure 5.4. Pre-processing Data Mode and Color Map Mode .................................................................... 47
Figure 5.5. Interactive 3D ............................................................................................................................ 48
Figure 5.6. Image+Spectroscopy - Display Spectral Data .......................................................................... 49
Figure 5.7. Locating SM4 Data Files ........................................................................................................... 50
Figure 6.1. Dashboard View of the IV Ramp Spectroscopy Settings ......................................................... 52
Figure 6.2. Spectroscopy - Alternate Scan Direction: Disabled .................................................................. 53
Figure 6.3. Spectroscopy - Alternate Scan Direction: Enabled................................................................... 53
Figure 6.4. Graphical Representation of Ramp Spectroscopy Timings ...................................................... 54
Figure 6.5. Scan Area Window access to Spectroscopy Procedures......................................................... 55
Figure 6.6. The Preconfigured UHV300 ihl ................................................................................................. 56
Figure 6.7. Dashboard for UHV300.ihl ........................................................................................................ 57