Schweitzer Engineering Laboratories SEL-421-4 - Page 774

xviii
SEL-400 Series Relays Instruction Manual Date Code 20171006
List of Figures
Figure 14.5 Example GOO S ALL L Command Response........................................................................14.30
Figure 14.6 Sample ID Command Response From Ethernet Card.............................................................14.34
Figure 14.7 Sample MAC Command Response .........................................................................................14.36
Figure 14.8 Sample PING Command Response.........................................................................................14.43
Figure 14.9 Sample TIME Q Command Response With IRIG ..................................................................14.60
Figure 14.10 Sample Time Q Command Response With PTP .....................................................................14.60
Figure 14.11 Sample VER Command Response ..........................................................................................14.62
Figure 15.1 Relay 4U Chassis Front-Panel Layout.......................................................................................15.2
Figure 15.2 Example 3U Rear-Panel Layout ................................................................................................15.3
Figure 15.3 Example 4U Rear-Panel Layout in Relay With Bay Cards.......................................................15.3
Figure 15.4 EIA-232 Connector Pin Numbers..............................................................................................15.3
Figure 15.5 Failover Network Topology ....................................................................................................15.10
Figure 15.6 Using Internal Ethernet Switch to Add Networked Devices...................................................15.11
Figure 15.7 SEL-2600A RTD Module and the Relay ................................................................................15.39
Figure 15.8 MET T Command Response ...................................................................................................15.40
Figure 15.9 MET T Command Response for Status Problem ....................................................................15.40
Figure 15.10 Example Direct Networking Topology ...................................................................................15.41
Figure 15.11 Example FTP Session..............................................................................................................15.43
Figure 15.12 Partial Contents of SET_P5.TXT ............................................................................................15.44
Figure 15.13 Telnet Connection Dialog Box ................................................................................................15.44
Figure 15.14 Example Telnet Session...........................................................................................................15.45
Figure 16.1 DNP3 Multidrop Network Topology ........................................................................................16.4
Figure 16.2 DNP3 Star Network Topology ..................................................................................................16.5
Figure 16.3 DNP3 Network With Communications Processor ....................................................................16.5
Figure 16.4 Sample Response to SHO D Command ..................................................................................16.24
Figure 16.5 Sample Custom DNP3 Analog Input Map Settings ................................................................16.26
Figure 16.6 DNP3 Application Network Diagram .....................................................................................16.26
Figure 16.7 SEL-421 Example DNP Map Settings ....................................................................................16.28
Figure 16.8 DNP3 LAN/WAN Application Example Ethernet Network...................................................16.31
Figure 16.9 Add Binary Inputs to SER Point List ......................................................................................16.33
Figure 17.1 MMS Client View of the CON Logical Device ........................................................................17.7
Figure 17.2 Relay Predefined Reports ........................................................................................................17.10
Figure 17.3 GOOSE Quality Attributes......................................................................................................17.13
Figure 17.4 Independent Bus Mode With PTP Time Synchronization on the Process Bus .......................17.19
Figure 17.5 Independent Bus Mode With PTP Time Synchronization on the Station Bus........................17.20
Figure 17.6 Independent Bus Mode With IRIG Time Synchronization .....................................................17.20
Figure 17.7 Merged Bus Mode With PTP Time Synchronization..............................................................17.20
Figure 17.8 Use Ethernet Switch to Engineer Network Path for GOOSE Messages. ................................17.21
Figure 17.9 Add ICD to Project Tree..........................................................................................................17.23
Figure 17.10 Configure an SV Publication...................................................................................................17.24
Figure 17.11 Example SV Publication Dataset.............................................................................................17.24
Figure 17.12 Configure SV Subscription......................................................................................................17.25
Figure 17.13 Send SEL-401 CID File...........................................................................................................17.25
Figure 17.14 Send SEL-421-7 CID File .......................................................................................................17.26
Figure 17.15 SEL-401 Publication Status.....................................................................................................17.26
Figure 17.16 SEL-421 SV Subscription Status.............................................................................................17.26
Figure 18.1 Synchrophasor Processing Block Diagram ...............................................................................18.3
Figure 18.2 Magnitude Frequency Response................................................................................................18.3
Figure 18.3 TCP Connection ......................................................................................................................18.14
Figure 18.4 UDP_T and UDP_U Connections ...........................................................................................18.15
Figure 18.5 UDP_S Connection..................................................................................................................18.15
Figure 18.6 Sample SEL-487E MET PM Command Response .................................................................18.22
Figure 18.7 Synchrophasor Control Application ........................................................................................18.34
Figure 18.8 PMU Global Settings...............................................................................................................18.35
Figure 18.9 Enabling Fast Operate Messages on Port 5 .............................................................................18.35
Figure 18.10 Ethernet Port 5 Settings for Communications Using C37.118 Extended Fame......................18.35