Schweitzer Engineering Laboratories SEL-421-4 - Page 773

xvii
Date Code 20171006 Instruction Manual SEL-400 Series Relays
List of Figures
Figure 9.5 Sample COMTRADE .HDR Header File..................................................................................9.11
Figure 9.6 Fixed Analog Section of an Example SEL-421 Event Report ..................................................9.15
Figure 9.7 Event Report Current Column Data and RMS Current Magnitude...........................................9.18
Figure 9.8 Event Report Current Column Data and RMS Current Angle ..................................................9.20
Figure 9.9 Digital Section of the SEL-411L Event Report.........................................................................9.22
Figure 9.10 Sample Digital Portion of the Event Report ..............................................................................9.23
Figure 9.11 Example Summary Section of the SEL-411L Event Report .....................................................9.24
Figure 9.12 Settings Section of the Event Report.........................................................................................9.24
Figure 9.13 Sample SEL-411L Event History ..............................................................................................9.27
Figure 9.14 Sample SER Report ...................................................................................................................9.29
Figure 9.15 Sample Compressed ASCII SER Report...................................................................................9.30
Figure 10.1 Remote Module Interface ..........................................................................................................10.3
Figure 10.2 Setting Main Board Outputs: QuickSet .....................................................................................10.8
Figure 10.3 Uploading Output Settings to the SEL-451...............................................................................10.9
Figure 10.4 Checking the 51S1 Overcurrent Element: QuickSet ...............................................................10.12
Figure 10.5 Setting SER Points and Aliases: QuickSet ..............................................................................10.13
Figure 10.6 Uploading Group 1 and Report Settings to SEL-451 ..............................................................10.14
Figure 10.7 SER Report: QuickSet HMI ....................................................................................................10.15
Figure 10.8 Relay Status: QuickSet HMI ...................................................................................................10.17
Figure 10.9 Relay Status From a STATUS A Command on a Terminal....................................................10.17
Figure 10.10 Example Compressed ASCII Status Message.........................................................................10.18
Figure 10.11 PS30 Power Supply Fuse Location .........................................................................................10.24
Figure 10.12 SEL-400 Series Relay Rear Panel ...........................................................................................10.25
Figure 10.13 Front-Panel Ribbon Cable Connector With Clasps Open .......................................................10.25
Figure 10.14 Main Board Cable Connections...............................................................................................10.26
Figure 10.15 I/O Board Jumper Configuration.............................................................................................10.26
Figure 10.16 Screw-Terminal Connector Receptacles..................................................................................10.27
Figure 10.17 Screw-Terminal Connector Keying.........................................................................................10.27
Figure 10.18 Screw-Terminal Connector With Webs...................................................................................10.28
Figure 10.19 I/O Board Installation Error Message in the Terminal Window .............................................10.29
Figure 10.20 Axion Notch Alignment ..........................................................................................................10.30
Figure 10.21 Axion Retaining Screw............................................................................................................10.31
Figure 11.1 PTP Time Synchronization Over a PRP Network.....................................................................11.4
Figure 11.2 Confirming the High-Accuracy Timekeeping Relay Word Bits ...............................................11.6
Figure 11.3 TLOCAL and TGLOBAL Logic...............................................................................................11.7
Figure 11.4 Sample TIM Q Command Response .........................................................................................11.8
Figure 11.5 Setting PMV64 With the Expression Builder Dialog Box ......................................................11.10
Figure 11.6 230 kV Transmission Line System..........................................................................................11.11
Figure 11.7 500 kV Three-Bus Power System ...........................................................................................11.12
Figure 11.8 Power Flow Solution ...............................................................................................................11.14
Figure 12.1 Typical Relay Settings Structure Overview ..............................................................................12.2
Figure 12.2 Changing a Default Name to an Alias .....................................................................................12.21
Figure 13.1 Protection and Automation Separation......................................................................................13.2
Figure 13.2 SEL
OGIC Control Equation Programming Areas ......................................................................13.3
Figure 13.3 Conditioning Timer With Pickup and No Dropout Timing Diagram .....................................13.16
Figure 13.4 Conditioning Timer With Pickup Not Satisfied Timing Diagram ..........................................13.17
Figure 13.5 Conditioning Timer With Dropout and No Pickup Timing Diagram .....................................13.17
Figure 13.6 Conditioning Timer With Pickup and Dropout Timing Diagram ...........................................13.18
Figure 13.7 Conditioning Timer Timing Diagram for Example 13.7.........................................................13.19
Figure 13.8 Sequencing Timer Timing Diagram ........................................................................................13.20
Figure 13.9 R_TRIG Timing Diagram .......................................................................................................13.27
Figure 13.10 F_TRIG Timing Diagram........................................................................................................13.28
Figure 14.1 Sample COM PTP Command Response .................................................................................14.14
Figure 14.2 Sample ETH Command Response ..........................................................................................14.23
Figure 14.3 GOOSE Command Response..................................................................................................14.29
Figure 14.4 Example GOO S Command Response ....................................................................................14.30