Schweitzer Engineering Laboratories SEL-421-4 - Page 762

vi
SEL-400 Series Relays Instruction Manual Date Code 20171006
List of Tables
Table 6.24 Autoreclose Logic Relay Word Bits..........................................................................................6.45
Table 7.1 MET Command ...........................................................................................................................7.1
Table 7.2 Instantaneous Metering Accuracy—Voltages, Currents, and Frequency ............................................7.3
Table 7.3 Instantaneous Metering Accuracy—Power .................................................................................7.4
Table 7.4 Rolling Demand Calculations......................................................................................................7.7
Table 7.5 Information Available With the MET ANA Command............................................................7.13
Table 8.1 Circuit Breaker Monitor Configuration.......................................................................................8.2
Table 8.2 Circuit Breaker Maintenance Information—Example.................................................................8.3
Table 8.3 Contact Wear Monitor Settings—Circuit Breaker 1 ...................................................................8.4
Table 8.4 Circuit Breaker Monitor Initiate SEL
OGIC Control Equations....................................................8.7
Table 8.5 Circuit Breaker Monitor Close SEL
OGIC Control Equations ......................................................8.9
Table 8.6 BRE Command..........................................................................................................................8.18
Table 8.7 DC Monitor Settings and Relay Word Bit Alarms....................................................................8.22
Table 8.8 Example DC Battery Voltage Conditions .................................................................................8.23
Table 8.9 Example DC Battery Monitor Settings—125 Vdc for Vdc1 and 48 Vdc for Vdc2..................8.23
Table 8.10 Example DC Battery Monitor Settings—AC Ripple Voltages .................................................8.24
Table 8.11 Example DC Battery Monitor Settings—Ground Detection Factor (EGADVS := Y)..............8.25
Table 9.1 Report Settings ............................................................................................................................9.8
Table 9.2 SUM Command.........................................................................................................................9.26
Table 9.3 HIS Command ...........................................................................................................................9.28
Table 9.4 SER Commands.........................................................................................................................9.30
Table 10.1 Acceptance Testing....................................................................................................................10.2
Table 10.2 Commissioning Testing.............................................................................................................10.2
Table 10.3 Maintenance Testing..................................................................................................................10.4
Table 10.4 Selectable Operating Quantity Time-Overcurrent Element (51S1) Test Settings...................10.10
Table 10.5 Alarm Relay Word Bits ...........................................................................................................10.15
Table 10.6 Troubleshooting Procedures....................................................................................................10.19
Table 10.7 Troubleshooting for Relay Self-Test Warnings and Failures..................................................10.20
Table 11.1 Relay Timekeeping Modes........................................................................................................11.2
Table 11.2 CUR_SRC Encoding .................................................................................................................11.5
Table 11.3 Time Quality Encoding (PTP Default Profile or IRIG) ............................................................11.5
Table 11.4 Time Quality Encoding (PTP Power Profile)............................................................................11.6
Table 11.5 Date/Time Last Update Sources ................................................................................................11.8
Table 11.6 SEL-421 Voltage and Current Measurement ..........................................................................11.12
Table 12.1 Typical Settings Classes and Instances .....................................................................................12.2
Table 12.2 Definitions for Active Setting Group Indication Relay Word Bits SG1 Through SG6 ............12.4
Table 12.3 Definitions for Active Setting Group Switching SEL
OGIC Control Equation Settings SS1
Through SS6.............................................................................................................................12.5
Table 12.4 Port Settings Categories.............................................................................................................12.6
Table 12.5 Protocol Selection......................................................................................................................12.7
Table 12.6 Communications Settings ..........................................................................................................12.7
Table 12.7 SEL Protocol Settings................................................................................................................12.7
Table 12.8 Fast Message Read Data Access................................................................................................12.7
Table 12.9 IP Configuration ........................................................................................................................12.8
Table 12.10 FTP Configuration.....................................................................................................................12.8
Table 12.11 HTTP Server Configuration ......................................................................................................12.9
Table 12.12 Telnet Settings ...........................................................................................................................12.9
Table 12.13 IEC 61850 Configuration ..........................................................................................................12.9
Table 12.14 SV Receiver Configuration .......................................................................................................12.9
Table 12.15 SV Transmitter Configuration ...................................................................................................12.9
Table 12.16 DNP3 Serial Protocol Settings ................................................................................................12.10
Table 12.17 DNP3 LAN/WAN Settings .....................................................................................................12.11
Table 12.18 Phasor Measurement Configuration ........................................................................................12.12
Table 12.19 M
IRRORED BITS Protocol Settings...........................................................................................12.12
Table 12.20 RTD Protocol Settings.............................................................................................................12.13
Table 12.21 PMU Protocol Settings ............................................................................................................12.14
Table 12.22 Simple Network Time Protocol (SNTP) Selection..................................................................12.14
Table 12.23 PTP Settings ............................................................................................................................12.14