Siemens SINUMERIK 828D - Page 15

Table of contents
Turning
Operating Manual, 01/2015, 6FC5398-8CP40-5BA2
15
9.2.8 Cut-off (CYCLE92) ................................................................................................................ 388
9.3 Contour turning ..................................................................................................................... 390
9.3.1 General information .............................................................................................................. 390
9.3.2 Representation of the contour .............................................................................................. 391
9.3.3 Creating a new contour ......................................................................................................... 392
9.3.4 Creating contour elements .................................................................................................... 394
9.3.5 Entering the master dimension ............................................................................................. 400
9.3.6 Changing the contour............................................................................................................ 402
9.3.7 Contour call (CYCLE62) - only for G code program ............................................................. 403
9.3.8 Stock removal (CYCLE952) .................................................................................................. 404
9.3.9 Stock removal rest (CYCLE952) ........................................................................................... 412
9.3.10 Plunge-cutting (CYCLE952) ................................................................................................. 415
9.3.11 Plunge-cutting rest (CYCLE952) .......................................................................................... 420
9.3.12 Plunge-turning (CYCLE952) ................................................................................................. 423
9.3.13 Plunge-turning rest (CYCLE952) .......................................................................................... 429
9.4 Milling .................................................................................................................................... 431
9.4.1 Face milling (CYCLE61) ....................................................................................................... 431
9.4.2 Rectangular pocket (POCKET3) ........................................................................................... 435
9.4.3 Circular pocket (POCKET4) .................................................................................................. 444
9.4.4 Rectangular spigot (CYCLE76) ............................................................................................ 454
9.4.5 Circular spigot (CYCLE77) ................................................................................................... 461
9.4.6 Multi-edge (CYCLE79) .......................................................................................................... 468
9.4.7 Longitudinal groove (SLOT1) ................................................................................................ 473
9.4.8 Circumferential groove (SLOT2) ........................................................................................... 482
9.4.9 Open groove (CYCLE899) .................................................................................................... 490
9.4.10 Long hole (LONGHOLE) - only for G code program ............................................................ 501
9.4.11 Thread milling (CYCLE70) .................................................................................................... 503
9.4.12 Engraving (CYCLE60) .......................................................................................................... 507
9.5 Contour milling ...................................................................................................................... 514
9.5.1 General information .............................................................................................................. 514
9.5.2 Representation of the contour .............................................................................................. 514
9.5.3 Creating a new contour ......................................................................................................... 516
9.5.4 Creating contour elements .................................................................................................... 519
9.5.5 Changing the contour............................................................................................................ 524
9.5.6
Contour call (CYCLE62) - only for G code program ............................................................. 525
9.5.7 Path milling (CYCLE72) ........................................................................................................ 526
9.5.8 Contour pocket/contour spigot (CYCLE63/64) ..................................................................... 532
9.5.9 Predrilling contour pocket (CYCLE64) .................................................................................. 534
9.5.10 Milling contour pocket (CYCLE63) ........................................................................................ 538
9.5.11 Contour pocket residual material (CYCLE63, option) ........................................................... 544
9.5.12 Milling contour spigot (CYCLE63) ......................................................................................... 547
9.5.13 Contour spigot residual material (CYCLE63, option) ............................................................ 552
9.6 Further cycles and functions ................................................................................................. 555
9.6.1 Swiveling plane / aligning tool (CYCLE800) ......................................................................... 555
9.6.2 Swiveling tool (CYCLE800) .................................................................................................. 563
9.6.2.1 Aligning turning tools - only for G code program (CYCLE800) ............................................. 563
9.6.2.2 Aligning milling tools - only for G code program (CYCLE800).............................................. 566
9.6.2.3 Preloading milling tools - only for G code program (CYCLE800) ......................................... 567
9.6.3 High-speed settings (CYCLE832) ......................................................................................... 568
9.6.4 Subroutines ........................................................................................................................... 572