Sony MVS-8000X SystemMVS-7000X System - Selecting Key Fill and Key Source

USO RESTRITO
128
Key Setting Operations Using Menus
Chapter
4
Keys
Parameter group [2/2]
Knob
Parameter
Adjustment
Setting values
1
Y Filter
Luminance
signal filter
coefficient
1 to 9
2
C Filter
Chrominance
signal filter
coefficient
1 to 9
When a wipe pattern key or key wipe pattern key is
selected
Knob
Parameter
Adjustment
Setting values
1
Size
Pattern size
0.00 to 100.00
2
Soft
Degree of edge
softness
0.00 to 100.00
3
Density
Key density
0.00 to 100.00
5 Make the following settings as required.
To invert the black and white sense of the key
source: Press [Key Invert], turning it on.
To adjust the horizontal position or key source
width for a luminance key, linear key, or
chroma key: Press [Key Position], turning it on,
and set the parameters.
Knob
Parameter
Adjustment
Setting values
1
H Phase
Key horizontal
position
–4.00 to +4.00
2
Left
Key left edge
position
–4.00 to +4.00
3
Right
Key right edge
position
–4.00 to +4.00
To set the key priority: Press [Key Priority] or select
VF7 ‘Misc’ and HF3 ‘Key Priority’ to access the
Key Priority menu.
For details, see “Setting the Key Priority by a Menu
Operation” (page 100).
Selecting Key Fill and Key Source
Notes
In the case of the MVS-8000X, only the premium inputs
(inputs to the switcher premium input connectors 1 to 20)
can be selected as key signals on the M/E-4 bank.
Selecting key fill and key source
To select key fill and key source for key 1 on the M/E-1
bank, use the following procedure.
1 In the M/E-1 >Key1 menu, select HF1 ‘Type.’
The Type menu appears.
2 In the <Key Fill> group, select either of the following
for use as key fill.
Key Bus: signal selected on the key 1 fill bus
Matte: signal from the dedicated color matte
generator
3 If you selected [Key Bus] in step 2, select the key fill
signal on the key 1 row in the cross-point control
block.
For the CCP-6224/6324 Control Panel, it is necessary
to set the [AUX CTRL] button to Off in order to exit
the AUX panel-less function (see page 92).
4 If you selected [Matte] in step 2, in the same Type
menu, press [Matte Adjust] to display the Matte Adjust
menu, then adjust the single-color or two-color
combination color matte. Select whether to use a
single-color matte or a two-color combination in the
<Fill Matte> group.
Flat Color: Adjust color 1 with the following
parameters.
Knob
Parameter
Adjustment
Setting values
1
Luminance
Luminance
0.00 to 100.00
2
Saturation
Saturation
0.00 to 100.00
3
Hue
Hue
359.99 to 0.00
Mix Color: Carry out a color mix. Adjust color 1 and
color 2, and select a mix pattern (see the next
section).
5 In the <Key Source> group, specify the key source
selection mode.
Self: The key fill bus signal is automatically selected
as the key source.
When the key type is selected as chroma key,
select [Self].
Auto Select: The signal allocated, being paired with
the key fill bus signal, to a cross-point button is
automatically selected as the key source. The
setting of key fill and key source pairs is carried
out in the Setup menu.
For details, see “Cross-Point Settings (Xpt Assign
Menu)” in Chapter 19 (Volume 2).
Split: You can select a key source signal
independently of the key source automatically
selected in Auto Select mode.
6 If [Split] was selected in step 5, hold down the
[SPLIT] button in the key control block or the
Multifunction Flexi Pad Control block, then in the
cross-point control block key 1 row, select the key