Sony MVS-8000X SystemMVS-7000X System - Applying a DME Effect to a Key

USO RESTRITO
Key Adjustments (Menus) 139
Chapter
4
Keys
2 In the <Mask Type> group, select the mask type.
Key Mask: Masks a part of a key.
Bkgd Mask: Masks a part of a background.
3 In the <Mask Source> group, select the mask source.
Wipe: wipe pattern selected for a transition
If you select [Wipe], select the pattern and make
modifier settings in the M/E-1 >Wipe menu (see
page 163), then return to this M/E-1 >Key1 menu.
In the case of a wipe pattern selected for a mask,
the modifier [Edge] and [Direction] settings are
not available.
Utility 1 Bus: signal selected on the utility 1 bus
When you selected [Utility 1 Bus], hold down the
[UTIL] button in the M/E-1 bank cross-point
control block, and select the signal with the
background A bus buttons. While the [UTIL]
button is pressed, the background A bus switches
to the utility 1 bus.
Notes
To enable the [UTIL] button, its operation mode must
be set to [Hold] beforehand.
For details, see “Assigning a Bus to an AUX
Delegation Button” in Chapter 19 (Volume 2).
4 Set the mask source parameters.
When wipe is selected
Knob
Parameter
Adjustment
Setting values
1
Size
Pattern size
0.00 to 100.00
2
Soft
Edge softness
0.00 to 100.00
When utility 1 bus is selected
Knob
Parameter
Adjustment
Setting values
1
Clip
Reference level
for creating
mask signal
+109.59 to
–7.31
2
Gain
Gain
–100.00 to
+100.00
5 To invert the black and white sense of the mask source,
press [Mask Invert], turning it on.
Applying a DME Effect to a Key
Notes
• When the SDI interface is used to connect the DME,
DME effects (including DME wipes) can be used in only
one place for one M/E bank.
• When the dedicated interface is used to connect the
DME, the number of keys to which DME effects
(including DME wipes) can be applied simultaneously
for one M/E bank varies as follows depending on the
execution mode of the DME wipe pattern selected for the
background.
- MVS-8000X
Applicable
block
Key to
which
DME
effects
are
applied
DME wipe
pattern for
background
Number of keys
to which DME
effects can be
applied
simultaneously
Other than
M/E-4
Keys 1
to 4
No DME
wipe used
2
One-channel
mode
1
Two- or
three-
channel
mode
0
Keys 5
to 8
-
2
a)
M/E-4
Keys 1
to 4
No DME
wipe used
2
b)
One-channel
mode
1
c)
Two- or
three-
channel
mode
0
Keys 5
to 8
-
0
- MVS-7000X
Key to
which
DME
effects are
applied
DME wipe pattern
for background
Number of keys to
which DME effects
can be applied
simultaneously
Keys 1 to 4
No DME wipe used
2
One-channel mode
1
Two- or three-
channel mode
0
Keys 5 to 8
-
2
a)
a) 0 when the system signal format is 1080P.
b) 1 when the system signal format is 1080P and the DME input/output
signal format is set to dual link mode.
c) 0 when the system signal format is 1080P and the DME input/output
signal format is set to dual link mode.
• When combining DMEs connected via the dedicated
interface and the SDI interface, you can increase the
number of keys to which DME effects are applied
simultaneously (requires a setting in setup).
For details, see “Setting DME and Switcher Interfaces”
in Chapter 20 (Volume 2).