Setting the Screen Aspect Ratio (Format Menu)
Chapter
18
System
Setup
(System)
The Format Converter menu appears.
3
To select the conversion format for SWR1 format
converter inputs 1 to 4, press [Input 1-4 Format] in the
<SWR1 FC Input> group.
A pop-up window appears.
4
Press the button for the desired signal format.
5
For “Input 5-8 Format” (MVS-8000X/7000X), and
“Input 9-12 Format” and “Input 13-16 Format” (MVS-
8000X only), set the desired signal format in the same
way as in steps 3 and 4.
6
To set the output format for format converters 1 and 2,
in the <SWR1 FC Output> group press [Output 1-2
Format], then press the button for the desired format.
7
For “Output 3-4 Format,” set the desired signal format
in the same way as in step 6.
8
With reference to steps 3 to 7, make the settings for
SWR2.
To delay unconverted input signals (frame delay
function)
When the signal format is 720P/59.94, 720P/50, 1080i/
59.94, or 1080i/50, you can press [Frame Delay] in the
pop-up window shown in step 3 and step 5 to delay input
signals.
For the format of the format converter input signal, the
same format as the signal format is shown.
Notes
•
The amount of delay that can be configured is given
below.
-
If the signal format is 1080i: up to 8 frames in 1-frame
units
-
If the signal format is 720P: up to 16 frames in 2-frame
units
The input signal must be synchronized to the reference
signal to obtain the same delay as that configured.
For details, see “Setting the Frame Delay Function”
(page 614).
•
You can use the frame delay function as a frame
synchronizer by setting the delay value to “1.” However,
the frame synchronizer introduces the following delay.
-
If the signal format is 1080i: 1 frame with respect to
the reference signal
-
If the signal format is 720P: 0.5 frames, 1 frame, or 1.5
frames with respect to the reference signal
Setting the Screen Aspect
Ratio (Format Menu)
Switch the screen aspect ratio to 16:9 or 4:3.
To set the screen aspect ratio, use the System >Format
menu.
Setting the screen aspect ratio
1
In the System >Format menu, press [Aspect].
The Aspect menu appears.
2
In the <Screen Aspect> group, select one of the
following.
• 16:9
• 4:3
•
Independ: Set the screen aspect ratio separately for
M/E, P/P, and USER on the switcher, and for each
channel independently on the DME.
3
If you selected [Independ] in step 2, select from the
following.
Switcher Aspect: Make the setting for the switcher.
DME Aspect: Make the setting for the DME.
A menu appears according to the selection.
4
Carry out either of the following, depending on the
selection you made in step 3.
When you selected [Switcher Aspect]: In each of the
<M/E-1>, <M/E-2>, <M/E-3>, <M/E-4>, <M/E-
5>,
<P/P>,
and
<USER>
groups,
select
either
[16:9] or [4:3].
When you selected [DME Aspect]: For each of the
<CH1> to <CH4> groups, select either [16:9] or
[4:3].
5
To confirm the above setting, press [Aspect Execute].
To cancel the setting and return to the original state,
press [Clear] without pressing [Aspect Execute].
When you press [Aspect Execute], a confirmation
message appears.
6
Press [Yes].
To Next Page
Loading...
