Sony MVS-8000X SystemMVS-7000X System - Kaleidoscope Settings; Lens Settings

USO RESTRITO
Applying Special Effects (Nonlinear Effect Settings) 323
Knob
Parameter
Adjustment
Setting value
s
2
V
Vertical
original
image
center
position
–16.000 to
+16.000
b)
a)
Knob
Parameter
Adjustment
Setting values
1
Magnify H
Horizontal
magnification
ratio
–100.00 to +100.00
2
Curve H
Horizontal
curve ratio
–100.00 to +100.00
Chapter
11
DME
Operations
–4.000 to +4.000
To cyclically repeat part of the original and its
reflection
Press [Cyclic], turning it on.
a) Setting for SD 4:3, SD 16:9
b) Setting for HD 4:3, HD 16:9
Lens Settings
You can set the shape and aspect ratio of the lens, the
angle, the magnification ratio, the curve ratio, the size, the
center position, and other parameters.
Kaleidoscope Settings
You can set the number of blocks, the partition reference
point and angle, horizontal and vertical offsets, a reflection
position, and other parameters.
To apply the Kaleidoscope effect
With the Kaleidoscope menu displayed, set the following
parameters.
Knob
Parameter
Adjustment
Setting values
1
Number
Number of
blocks
0.00 to 100.00
2
Phase
Angle of
partition
reference point
–8.000 to +8.000
3
Offset H
Amount of
horizontal
offset
–4.000 to +4.000
a)
–16.000 to +16.000
b)
4
Offset V
Amount of
vertical offset
–3.000 to +3.000
a)
–12.000 to +12.000
b)
a) Setting for SD 4:3, SD 16:9
b) Setting for HD 4:3, HD 16:9
To reflect the kaleidoscope image as if in a mirror
1 To reflect in the horizontal direction, press [Mirror H],
turning it on.
2 To reflect in the vertical direction, press [Mirror V],
turning it on.
To set the reflection position
1 Press [Position], turning it on.
2 Set the following parameters.
Knob
Parameter
Adjustment
Setting values
1
H
Horizontal
reflection
position
0.000 to 4.000
a)
0.000 to 16.000
b)
2
V
Vertical
reflection
position
0.000 to 3.000
a)
0.000 to 12.000
b)
a) Setting for SD 4:3, SD 16:9
b) Setting for HD 4:3, HD 16:9
You can also choose to display only the portion of the
image that is seen through the lens.
To apply the Lens effect
With the Lens menu displayed, use the following
procedure.
1 In the <Mode> group, select the lens shape.
• Circle
• Rectangle
• Star
• Heart
• Bar
• Cross
2 Depending on the selected lens shape, set the
following parameters.
When Circle, Rectangle, Star, or Heart is selected
Knob
Parameter
Adjustment
Setting values
1
Magnify H
Magnification
ratio
–100.00 to +100.00
2
Curve H
Curve ratio
–100.00 to +100.00
3
Size H
Size
0.00 to 100.00
4
Angle
Slant angle
–8.000 to +8.000
5
Aspect
Aspect ratio
–100.00 to +100.00
When Bar is selected
Knob
Parameter
Adjustment
Setting values
1
Magnify H
Magnification
ratio
–100.00 to +100.00
2
Curve H
Curve ratio
–100.00 to +100.00
3
Size H
Size
0.00 to 100.00
4
Angle
Slant angle
–8.000 to +8.000
When Cross is selected
Parameter group [1/2]