Sony MVS-8000X SystemMVS-7000X System - Applying Special Effects (Edge Effects); Border Settings

USO RESTRITO
Applying Special Effects (Edge Effects) 289
Knob
Parameter
Adjustment
Setting values
1
H
Border width
on left and
right sides
Left value shown
2
V
Border width
on top and
bottom sides
Top value shown
3
All
Border width
on all sides
Left value shown
5
Density
Border
density
0.00 to 100.00
Knob
Parameter
Adjustment
Setting values
1
Top
Border width
on top side
–4.50 to +4.50 (SD)
–18.00 to +18.00
(HD)
2
Left
Border width
on left side
–8.00 to +8.00 (SD)
–32.00 to +32.00
(HD)
3
Right
Border width
on right side
–8.00 to +8.00 (SD)
–32.00 to +32.00
(HD)
4
Bottom
Border width
on bottom
side
–4.50 to +4.50 (SD)
–18.00 to +18.00
(HD)
5
Density
Border
density
0.00 to 100.00
Knob
Parameter
Adjustment
Setting values
1
H
Border width
on left and
right sides
Left value shown
2
V
Border width
on top and
bottom sides
Top value shown
3
All
Border width
on all sides
Left value shown
5
Density
Border
density
0.00 to 100.00
Knob
Parameter
Adjustment
Setting values
1
Top
Border width
on top side
–6.00 to +6.00 (SD)
–18.00 to +18.00
(HD)
2
Left
Border width
on left side
–8.00 to +8.00 (SD)
–24.00 to +24.00
(HD)
3
Right
Border width
on right side
–8.00 to +8.00 (SD)
–24.00 to +24.00
(HD)
4
Bottom
Border width
on bottom
side
–6.00 to +6.00 (SD)
–18.00 to +18.00
(HD)
5
Density
Border
density
0.00 to 100.00
Chapter
11
DME
Operations
Applying Special Effects
(Edge Effects)
16:9 mode
Parameter group [1/2]
Border Settings
Adding a border
1 In the DME menu, select VF1 ‘Edge’ and HF1
‘Border/Crop.’
The Border/Crop menu appears.
2 Press [Border], turning it on.
3 Set the parameters.
The valid ranges of the parameter values depend on the
combination of signal format (SD/HD) and aspect
ratio (4:3/16:9) selected in the system, as follows.
4:3 mode
Parameter group [2/2]
Parameter group [1/2]
Parameter group [2/2]
Setting the border color
The operation differs depending on the DME used (MVE-
8000A, MVE-9000 or MKS-7470X/7471X).
When the MVE-8000A is used
Press [Border Color], turning it on, and set the following
parameters.
Knob
Parameter
Adjustment
Setting values
1
Luminance
Luminance
0.00 to 100.00
2
Saturation
Saturation
0.00 to 100.00
3
Hue
Hue
359.99 to 0.00
When the MVE-9000 or MKS-7470X/7471X is used
Use the buttons in the <Border Fill> group to select the
signal to insert in the border.
Flat Color: single color
Mix Color: mix color signal set in the Color Mix menu
(see page 302)
Ext Video: an external video signal input to the Ext IN
connector
If Flat Color is selected, adjust the following parameters.
Knob
Parameter
Adjustment
Setting values
1
Luminance
Luminance
0.00 to 100.00