Chapter
8
Color
Backgrounds,
Copy
and
Swap,
and
Other
Settings
Misc Menu Operations
In the Misc menu, you can carry out the following
operations.
•
Enabling and disabling operation from an external
device, System Manager, or an editing keyboard.
•
Enabling and disabling side flags on the background bus
of each of the M/E-1 to M/E-5 and PGM/PST banks.
For the side flag function, see “Side Flags” (page 250).
•
Switching the safe title function on or off for each
switcher output.
•
Displaying the transition rate, independent key transition
rate, and fade-to-black transition rate for each of the M/
E and PGM/PST banks, and changing the settings.
•
Setting the AUX mix transition rate.
DME override
1
In the menu control block, press the top menu
selection button [MISC], then select VF1 ‘Enable’ and
HF1 ‘Port Enable.’
The Misc >Enable >Port Enable menu appears.
2
In the <DME Override> group, select the DME
override mode.
DME Override: When a switcher snapshot or effect
using a DME is recalled, forcibly select the DME
that was used when saving.
On Air Protect: The operation is the same as the
DME override function, except that a DME being
used by an M/E bank or P/P bank that is on air will
not be forcibly selected.
Port Settings for Control From an
External Device
Enabling or disabling control from an
external device
1
In the menu control block, press the top menu
selection button [MISC], then select VF1 ‘Enable’ and
HF1 ‘Port Enable.’
The Misc >Enable >Port Enable menu appears with
the status area showing the settings of the following
ports.
•
Switcher Remote1 to Remote4 ports (RS-422A, D-
sub 9-pin)
•
Switcher GPI port (parallel, 25-pin)
•
DME1/DME2 Editor ports (RS-422A, D-sub 9-pin)
•
DME1/DME2 GPI ports (parallel, 25-pin)
When the signal format is 1080P, you can also make
settings for DME3/DME4.
2
In the <Switcher> or <DME> group, press on the
name of the port for which you want to disable control
from an external device, turning it off.
To re-enable control for the port, press on its name
once more.
Notes
For the AUX bus operation from the Remote 1 to
Remote 4 ports of the switcher, the setting (Enable/
Disable/Manual) in the Setup menu takes precedence.
Only when the setting is “Manual,” the settings made
in the Port Enable menu apply.
For details, see “Interfacing With External Devices
(Device Interface Menu)” in Chapter 19 (Volume 2).
Notes
If effects using the same DME channel are selected
simultaneously in two or more regions, the DME is
selected with the order of precedence P/P >M/E1 >M/
E2 >M/E3 >M/E4 >M/E5.
Enabling or disabling control from System
Manager
By installing the BZPS-8000 System Management
Software (System Manager), you can use a computer
connected on a network for management of some switcher
data and control operations.
To enable or disable this function, use the following
procedure.
1
In the menu control block, press the top menu
selection button [MISC], then select VF1 ‘Enable’ and
HF1 ‘Port Enable.’
The Misc >Enable >Port Enable menu appears.
2
Press [System Manager].
Each time you press the button toggles between enable
and disable.
Editing Keyboard Settings
Notes
The following operations are only possible when a license
for the BZS-8050 Editing Control Software is activated.
For details of license registration, see “Installation and
Device Setup (Install/Unit Config Menu)” in Chapter 18
(Volume 2).
To Next Page
Loading...
