Chapter
8
Color
Backgrounds,
Copy
and
Swap,
and
Other
Settings
•
DME: Copying and swapping data by DME channels
•
Format Converter: Copying format converter data
For an overview of the concepts involved, see “Copy and
Swap” (page 230). For details of color corrector copy
and swap, see “Copy and Swap Operations” (page 241).
Examples of Copy and Swap operations by
a menu operation
As an example, to copy or swap wipe data, use the
following procedure.
1
In the Copy/Swap menu, select HF3 ‘Wipe.’
The Copy/Swap >Wipe menu appears.
The status area shows lists for the copy/swap source on
the left, and the copy/swap destination on the right.
2
In the <Data Select> group, select either of the
following.
Wipe: The operation applies to wipes in the transition
control block.
Key Wipe: The operation applies to wipes in the
independent key transition control block.
3
Using any of the following methods, select the data to
be copied or swapped.
•
Press directly on the list in the status area.
•
Press the arrow keys to scroll the reverse video
cursor.
•
Turn the knobs to make the setting.
Select data for
copy/swap
source
Select data for
copy/swap
destination
a)
The following values apply to the MVS-8000X.
Transition control block wipe data: 1 to 5
Transition control block for independent key wipe data: 1 to 40
b)
The following values apply to the MVS-7000X.
Transition control block wipe data: 1 to 6
Transition control block for independent key wipe data: 1 to 48
For details of the data affected, see “Copy and Swap”
(page 230).
4
To copy, press [Copy], and to swap, press [Swap].
To undo a copy or swap
Press [Undo], to return to the state before the copy or swap
was carried out.
Copy by Button Operation
You can carry out the following copy operations by a
simple button operation.
•
M/E copy
•
Keyer copy
•
Wipe copy
•
DME wipe copy
Notes
On the CCP-6224/6324, it is not possible to carry out a
copy by button operation.
Basic button operation
The basic button operation is to hold down the copy source
button, then press the destination button.
You can undo the last operation using [Undo] in the menu
(see page 232).
M/E copy button operation
In the Flexi Pad control block of each M/E bank, use the
[SNAPSHOT] button.
To copy from M/E-1 to M/E-2
In the M/E-1 Flexi Pad control block, hold down the
[SNAPSHOT] button, then press the [SNAPSHOT] button
in the M/E-2 Flexi Pad control block.
Keyer copy button operation
To specify the copy source, use the key delegation buttons
in the key control block, and to specify the copy
destination, use the key delegation buttons in the
independent key transition control block.
To copy from M/E-1 key 1 to M/E-2 key 2
In the key control block M/E delegation buttons, press [M/
E 1], turning it on, then hold down the [KEY1] button, and
in the M/E-2 independent key transition control block,
press the [KEY2] button.
Wipe copy button operation
Use the [WIPE] button in the Flexi Pad control block of
each M/E bank.
To copy the M/E-1 wipe to the M/E-2 wipe
In the M/E-1 Flexi Pad control block, hold down the
[WIPE] button, then press the [WIPE] button in the M/E-2
Flexi Pad control block.
DME wipe copy button operation
Use the [DME] button in the Flexi Pad control block of
each M/E bank.
To copy the M/E-1 DME wipe to the M/E-2 DME
wipe
In the M/E-1 Flexi Pad control block, hold down the
[DME] button, then press the [DME] button in the M/E-2
Flexi Pad control block.
To Next Page
Loading...
