Operation Settings (Operation Menu)
Chapter
19
Control
Panel
Setup
(Panel)
Operation Settings
(Operation Menu)
To make settings relating to panel operation, use the Panel
>Operation menu.
To display the Operation menu
In the Engineering Setup menu, select VF2 ‘Panel’ and
HF6 ‘Operation.’
The status area shows the items that can be set and a list of
the settings.
The following functions are available here.
•
Button Tally: Set whether or not the system tally
generation results are reflected in the panel tally.
-
[TRANS PVW] button
-
[UTIL] button
-
[XPT HOLD] button in key rows
-
Selection of signal assigned to the key source bus
(either key signal only, or either video signal or key
signal selectable)
•
Sensitivity: Adjust trackball, joystick and double-click
sensitivity, or set the relationship between the angle of
the search dial and the playback speed or the sensitivity
for the search dial in jog mode.
•
Main Split Fader: When the split fader is active,
specify whether the fader to control other than mix is the
left side or the right side.
•
Macro: Set the macro execution mode and the mode in
which to edit macros using the standard type Flexi Pad
control block.
•
Key Row Operation: Set the operation mode for cross-
point control block key 1 and key 2 rows.
•
Trans Rate Display: Select whether the transition rate
display mode is in frames or timecode units.
•
S-Bus Name Link: Copy the S-Bus description name to
the source name.
•
Effect: For keyframe effects, you can make the
following settings.
-
Recall mode
-
Automatically turning off the [EDIT ENBL] button
when an effect is recalled
-
Automatic insertion of a first keyframe when an empty
register is recalled
-
Effect Auto Save
-
Default KF Duration
-
Setting whether or not to replay the first keyframe after
rewinding a GPI/P-Bus/disk recorder/VTR/Extended
VTR/Macro effect
•
Source/Dest Name: For the Source/Dest (source/
destination) names used by the system, select one of the
following:
Setting the On-Air Tally
To set the high tally state reflected on the control panel, use
the following procedure.
1
In the Panel >Operation menu, press [Button Tally].
The Button Tally menu appears.
2
In the <Tally Type> group, select either of the
following.
[R1] to [R8]: Reflect any of tally groups 1 to 8 as the
tally state.
Independent: Reflect only the switcher tally state.
3
Press [Execute].
A popup window appears and shows the progress of
the operation.
- Source name set by cross-point assignment or fixed
bus name
-
Description name set on routing switcher
-
“Type + Num” name set on routing switcher
Names assigned with Xpt Assign can be replaced later with
description names.
•
Name Display: Specify the number of characters for
display of the names selected in Source/Dest Name
above, as two characters, four characters, or Auto.
•
Flexi Pad Mode: Carry out Flexi Pad settings. Specify
the delegation selection coupling, and display mode for
the LCD buttons. You can also make menu settings for
wipe snapshots.
•
Custom Button: Set the following button operation
modes.
-
[ALL] button for next transition selection
-
[AUTO TRANS], [TAKE] or [FTB] button during
auto transition execution
-
[RUN] button during keyframe execution
-
[AUTO TRANS] and [CUT] button replacement
Assigning a Key or AUX Bus to a
Button in the Key 1 or Key 2 Row
These settings enable keys 1 to 8 and AUX bus selection
in the key 1 and key 2 rows of the cross-point control
block.
1
In the Panel >Operation menu, press [Key Row
Operation].
The Key Row Operation menu appears.
2
In the <Key Row Mode> group, select one of the
following.
Key Bus: Use the key 1 and key 2 rows as cross-point
button rows for the keyers.
To Next Page
Loading...
