Sony MVS-8000X SystemMVS-7000X System - Enabling or Disabling AUX Bus Control; Setting the Interface between the DME and the Switcher

USO RESTRITO
Interfacing With External Devices (Device Interface Menu) 633
1
In the Switcher >Device Interface menu, press [DME
Type Setting].
The DME Type Setting menu appears.
2
In the <DME1 Type> group to set DME1 or in the
<DME2 Type> group to set DME2, press either of the
following, turning it on.
Dedicated: The DME has an dedicated interface.
SDI: The DME has an SDI interface.
Notes
If the system signal format is set to 1080P and the
DME input/output signal format is set to Dual Link
Mode, the SDI interface cannot be selected.
For details of the connection of DME units and the
switcher, see “MVS-8000X-/7000X-C Installation
Manual.”
Chapter
20
Switcher
Setup
(Switcher)
M/E-1 to M/E-5 and P/P: Set an action for the M/E or
PGM/PST bank.
Common: Set an action for error status.
6 Using any of the following methods, select the action
to be set.
• Press directly on the list appearing in the status area.
• Press the arrow keys to scroll the reverse video
cursor.
• Turn the knobs.
Knob
Parameter
Adjustment
Setting values
2
Action
Action selection
1 to maximum
value
a)
5
Reg No
Register number
1 to 4
b)
1 to 99
c)
a) Action list when the trigger type is other than “Status”
In M/E-x, the x is the M/E bank number (1 to 5); in DSKx the x is the
DSK number (1 to 8); in Keyx the x is the key number (1 to 8).
- When Source is M/E-x: Cut, Auto Trans, Keyx Cut, Keyx Auto
Trans, Keyx SS ? Recall, Effect ? Recall, Effect ? Recall & Run,
KF Run, KF Stop, KF Rewind, No Action
- When Source is P/P: Cut, Auto Trans, DSKx Cut, DSKx Auto
Trans, FTB Cut, FTB Auto Trans, DSKx SS ? Recall, Effect ?
Recall, Effect ? Recall & Run, KF Run, KF Stop, KF Rewind, No
Action
- When Source is Common: No Action
Action list when the trigger type is “Status”
In M/E-x, the x is the M/E bank number (1 to 5); in DSKx the x is the
DSK number (1 to 8); in Keyx the x is the key number (1 to 8).
- When Source is M/E-x: Keyx On, No Action
- When Source is P/P: DSKx On, No Action
- When Source is Common: Error Make, Error Break, No Action
b) When knob 2 selection is “Key Snapshot”
c) When knob 2 selection is “Snapshot” or “Effect”
7 Press [Action Set] to confirm the action selection.
The selected setting appears in the status area.
Test firing the trigger
To test fire the trigger, press [Test Fire].
This outputs a trigger from the selected output port. This is
not output when the trigger type is “Status.”
Remote4: Make the settings for the REMOTE4 port.
3 Using any of the following methods, select the AUX
bus.
• Press directly on the list in the status area.
• Press the arrow keys to scroll the reverse video
cursor.
• Turn the knob.
Knob
Parameter
Adjustment
Setting values
1
No
AUX bus
selection
0 to 48
a)
a) 0: EDIT PVW
1 to 48: AUX1 to AUX48
4 Select whether to enable or disable AUX bus control
from the <Control Mode> group.
Enable: enable control of the port selected in step 2.
Disable: disable control of the port selected in step 2.
Manual: make whether control of the port selected in
step 2 is possible or not depend on the setting in
the Misc menu.
5 Repeat steps 2 to 4 as required to make the settings for
other ports.
Setting the Interface Between the
DME and the Switcher
To set the interface between the DME and the switcher,
proceed as follows.
Enabling or Disabling AUX Bus
Control
1 In the Switcher >Device Interface menu, press [Aux
Control].
The Aux Control menu appears.
2 Select the 9-pin port for the setting, from the
<Control> group.
Remote1: Make the settings for the REMOTE1 port.
Remote2: Make the settings for the REMOTE2 port.
Remote3: Make the settings for the REMOTE3 port.