Sony MVS-8000X SystemMVS-7000X System - Output Video Processing Operations

USO RESTRITO
Color Corrector Functions 247
Knob
Parameter
Adjustment
Setting values
1
Video Gain
Video signal
gain
–200.00 to +200.00
2
Y Gain
Y signal gain
–200.00 to +200.00
3
C Gain
Chrominance
signal gain
–200.00 to +200.00
4
Hue Delay
Hue delay
–180.00 to +180.00
5
Black
Level
Black level
–116.90 to +116.90
Knob
Parameter
Adjustment
Setting values
1
Luminance
Luminance
–7.31 to +109.59
2
Saturation
Saturation
0.00 to 100.00
3
Hue
Hue
359.99 to 0.00
4
Gain
Key gain
–100.00 to +100.00
Knob
Parameter
Adjustment
Setting values
1
Luminance
Luminance
0.00 to 100.00
Chapter
9
Color
Corrector
Adjusting the color of the specified region
(key)
1 In the CCR menu, press VF1 ‘CCR1’ and HF6 ‘Spot
CCR/Output.’
The Spot CCR/Output menu appears.
2 In the <Spot CCR> group, press [Spot CCR], turning
it on.
3 In the <Auto> group, press [Sample Mark], turning it
on.
Notes
When [Sample Mark] is on, the effects of color
adjustment outside the region of spot color adjustment
(see page 247) and output video processing (see page
248) are temporarily disabled.
Turning [Sample Mark] off restores the former state.
4 Adjust the parameters so that the color you want to
change is included within the sample mark.
Knob
Parameter
Adjustment
Setting values
1
Position H
Horizontal
position
–100.00 to +100.00
2
Position V
Vertical
position
–100.00 to +100.00
3
Size
Size
1.00 to 100.00
5 In the <Auto> group, press [Auto Start], to adjust the
key automatically.
Knob
Parameter
Adjustment
Setting values
2
Saturation
Saturation
0.00 to 100.00
3
Hue
Hue
0.00 to 100.00
8 In the <Spot CCR> group, press [Spot CCR] to display
the parameters, and adjust the replacement color.
.
Knob
Parameter
Adjustment
Setting values
1
Luminance
Luminance
0.00 to 100.00
2
Saturation
Saturation
0.00 to 100.00
3
Hue
Hue
359.99 to 0.00
To return the parameters to their default settings
In the <Spot CCR> group, press [Unity].
Masking a part of the spot color
adjustment
Set [Mask] to On in the Spot CCR/Output menu, then carry
out the same procedure as in “Masking a part of the
primary color correction” (page 243).
Adjusting the color outside the spot color
adjustment region
1 In the Spot CCR/Output menu, press [Outer Out Proc]
in the <Outer Out Proc> group, turning it on.
2 Adjust the following parameters.
Notes
This automatic adjustment does not carry out key gain
adjustment. If required, adjust the key gain as shown
in step 6.
6 Press [Key Adjust], and adjust the following
parameters.
To return the parameters to their default settings
In the <Outer Out Proc> group, press [Unity].
Output Video Processing Operations
7 Press [Window], turning it on, to adjust the key
detection range for spot color adjustment.
The following corrections are available for the YUV
signal.
• Video signal overall gain adjustment
• Y signal gain adjustment
• Y signal offset adjustment
• C signal gain adjustment
• C signal hue adjustment