Sony MVS-8000X SystemMVS-7000X System - Operation Buttons

USO RESTRITO
46
Names and Functions of Parts of the Control Panel
Selected
buttons
Overview of assigned operation
[M/E1] to
[M/E5],
[P/P]
• This enables the wipe pattern position
setting (positioner) operation mode in the
device control block.
• You can select multiple buttons
simultaneously.
For details of [M/E4] or [M/E5] button
assignment, see “Assigning a Button for M/E-
4 or M/E-5 Selection in the Setup Menu”
(page 396) in Appendix.
[USER]
This enables pattern position setting used for
color backgrounds.
[DME1] to
[DME8]
• This enables the three-dimensional
transform operation mode in the device
control block.
• Press a button, turning it on, to select a
DME channel.
• You can select multiple buttons
simultaneously.
• The number of valid buttons depends on the
number of DME processor channels
installed.
[DEV]
• This enables the VTR/disk recorder/frame
memory operation mode in the device
control block.
• Each button functions as follows.
(From upper left to right in the above figure)
- [M/E1] to [M/E3]: DEV1 (device 1) to
DEV3 (device 3)
- [P/P]: DEV4 (device 4)
- [USER]: FM1CLIP (frame memory clip 1)
- [Unused]: FM2CLIP (frame memory clip
2)
- [DME1] to [DME4]: DEV5 (device 5) to
DEV8 (device 8)
- [FX CTRL]: FM LOOP (frame memory
loop)
- [DME5] to [DME8]: DEV9 (device 9) to
DEV12 (device 12)
• To exit from this mode, press the [DEV]
button again, turning it off.
[RUN
CTRL]
This enables the effect run control mode in
the device control block.
[RSZR
CTRL]
• This enables the resizer control mode in the
device control block.
• In resizer control mode, select the key with
the region selection button [K1RSZ] to
[K8RSZ].
Chapter
2
Menus
and
Control
Panel
Selected
buttons
Overview of assigned operation
[FX CTRL]
Leave this button off for operation.
Alternatively, for details of operation of this
button, refer to the help information for the
MPES-FX01 Programmable Effector software.
b Operation buttons
The following buttons are used to carry out the
corresponding operations. Function of each button varies
with the operation mode.
When the positioner operation mode is enabled
For details of assignment of keys 5 to 8, see “Assigning
Buttons for Selection of Keys 5 to 8 in the Setup Menu”
(page 397) in Appendix.
Name
Description
K1 CB1
a) b)
• Press this button to enable wipe pattern
position setting for key 1 (DSK1).
• When the [USER] button is selected,
pattern position setting for color background
1 is enabled.
K2 CB2
a) b)
• Press this button to enable wipe pattern
position setting for key 2 (DSK2).
• When the [USER] button is selected,
pattern position setting is enabled for color
background 2.
K3
a) b)
Press this button to enable wipe pattern
position setting for key 3 (DSK3).
K4
a) b)
Press this button to enable wipe pattern
position setting for key 4 (DSK4).
MAIN
a)
Press this button to enable main wipe pattern
position setting for normal transitions.
SB
a)
Press this button to enable sub wipe pattern
position setting for normal transitions.
POS
• Press this button to enable pattern
movement in the X-axis and Y-axis
directions with the trackball.
• When the [USER] button is selected, this
enables the trackball to move the pattern in
the X-axis and Y-axis directions, and the
Z-ring to adjust the size of the pattern.
X, Y, Z
These restrict the axes affected by the
trackball and Z-ring to the X-, Y- or Z-axis.