Sony MVS-8000X SystemMVS-7000X System - Page 475

USO RESTRITO
Snapshot Operations From the Numeric Keypad Control Block 475
The first pressed button lights green as the reference
region, and subsequently pressed buttons light amber.
Pressing one of the amber-lit buttons, while holding
down [SNAPSHOT], turns the button green to indicate
its corresponding region as the new reference region.
For details of the precedence order for becoming the
reference region, see “Reference region” (page 434).
The display shows the name of the reference region
and the number of the register previously recalled for
that region.
3
Enter the desired register number from the numeric
keypad.
The entered register number appears in the display.
4
To apply temporary attributes (see page 474), press the
following buttons, turning them on.
Chapter
14
Snapshots
6 To apply attributes (see page 472), press the following
buttons, turning them on.
Attribute to apply
Button
Effect dissolve
[+/–/EFF DISS] button
Auto transition
[CLR/AUTO TRANS] button
GPI output
a)
[TRIM/GPI ENBL] button
a) The GPI port that can be set is 1 (fixed).
Notes
In the numeric keypad control block, it is not possible
to apply the cross-point hold.
For details, see “Applying snapshot attributes” (page
482).
7 Press the [ENTER] button.
This saves the snapshot, and the [STORE] button goes
off. The [RCALL] and [STORE STATS] buttons light.
To cancel a snapshot save operation
Hold down the [STORE STATS] button and press the
[UNDO] button.
Recalling a snapshot from the numeric
keypad control block
1 In the numeric keypad control block, press the
[SNAPSHOT] button, turning it on.
This allocates the numeric keypad control block to
snapshot operations, and the [RCALL] button lights.
2 Press the region selection button corresponding to the
region you want to recall, turning it on. Multiple
selections are also possible.
[M/E 1], [M/E 2], [M/E 3], [M/E 4], [M/E 5], [P/P]:
These select the corresponding M/E-1, M/E-2, M/
E-3, M/E-4, M/E-5, and PGM/PST regions.
[USER 1] to [USER 8]: These select the User regions.
[DME 1] to [DME 8]: These select the DME
channels.
[RTR]: This selects the Router region.
[ALL]: This selects all regions.
[MASTR]: This selects a master snapshot.
Notes
The regions that can be selected simultaneously are
those assigned to the region selection buttons in the
numeric keypad control block (see page 570).
It is not possible to select [MASTR] and other regions
simultaneously. If selected simultaneously, the master
snapshot takes precedence.
Control
block
Temporary
attribute to apply
Button
Cross-point
control block
A/B bus cross-
point hold
[XPT HOLD] button
in the background
A/B bus
Key cross-point
hold
[XPT HOLD] button
in the key bus
a)
Key disable
[XPT HOLD] button
in the key bus
b)
Numeric
keypad
control block
Effect dissolve
[+/–/EFF DISS]
button
Auto transition
[CLR/AUTO
TRANS] button
a) When Xpt Hold mode is selected in setup.
b) When Key Disable mode is selected in setup.
For the setup setting, see “Setting the operation mode
of the key bus [XPT HOLD] button” (page 625).
Notes
• The cross-point hold and key disable settings are
maintained until you next press the [XPT HOLD]
button.
• Applying temporary attributes does not affect the
contents of the register.
• It is not possible to apply temporary attributes to a
master snapshot.
5 Press the [ENTER] button.
This recalls the specified snapshot, and the reference
region name and recalled register number appear in the
display.
If you applied the effect dissolve or auto transition
temporary attributes in step 4, the corresponding
buttons go off.