Sony MVS-8000X SystemMVS-7000X System - Page 517

USO RESTRITO
Macro Attachment Assigning 517
Block
Button
Cross-point control
block
• Background A row cross-point
buttons
• Background B row cross-point
buttons
• Key 1 bus cross-point buttons
• Key 2 bus cross-point buttons
• Key 3 bus cross-point buttons
• Key 4 bus cross-point buttons
• Key 5 bus cross-point buttons
a)
• Key 6 bus cross-point buttons
a)
• Key 7 bus cross-point buttons
a)
• Key 8 bus cross-point buttons
a)
• Utility 1 bus cross-point buttons
• Utility 2 bus cross-point buttons
• DME external video bus cross-
point buttons
• DME utility 1 bus cross-point
buttons
• DME utility 2 bus cross-point
buttons
• Memory recall buttons
b)
• Buttons set to “Inhibit”
• Auxiliary bus cross-point row
c)
Auxiliary bus control
block
• Cross-point button1st row
d)
• Cross-point button 2nd row
d)
Keyframe control
block
• [RUN], [REWIND] and [FF]
buttons
• [NORM], [REV], and [NORM/
REV] buttons
Device control block
(trackball, joystick)
Buttons assigned the same function
as the [PLAY], [CUE], [STOP], and
[START TC] buttons for VTRs/disk
recorders/Extended VTRs/frame
memory clips
Device control block
(search dial)
[PLAY], [CUE], [STOP] and [START
TC] buttons
Downstream key
control block
• [DSK1 ON] to [DSK8 ON]
buttons
e) g)
• [KEY1 ON] to [KEY8 ON]
buttons
a) e)
• [TAKE] button
e)
• [MIX], [WIPE], [DME], and [CUT]
buttons
Transition control
block
Fader and buttons assigned with the
following functions.
• Next transition selection
• Transition type selection
• Wipe direction selection
• Auto transition, cut
• Device operation (CUE, PLAY,
STOP)
• Pattern limit on/off
• Independent key transition type
selection
• Independent key transition auto-
transition, cut
e)
Fade to black control
block
[FTB] button
Chapter
16
Macros
Block
Button
Downstream key/fade
to black control block
• [DSK1 ON] and [DSK2 ON]
buttons
e)
• [DSK3 ON] to [DSK8 ON]
buttons
a) e)
• [KEY1 ON] to [KEY8 ON]
buttons
a) e)
• [AUTO TRANS] button
e)
• [FTB] button
Utility/shotbox control
block
Memory recall buttons
Menu control block
[PREFS 1] to [PREFS 16] buttons
Independent key
transition control
block (simple type)
f)
• [KEY1 ON] to [KEY8 ON]
buttons
e) g)
• [DSK1 ON] to [DSK8 ON]
buttons
e) g)
• [TAKE] button
e)
• [MIX], [WIPE], [DME], and [CUT]
buttons
Multifunction Flexi
Pad control block
[AUTO TRANS]
e)
, [KEY ON]
e)
,
[RUN], [REWIND], [NORM], [REV]
and [NORM/REV] buttons
a) Assignment is required
b) Only when key row is operated in the utility/shotbox mode
c) When the auxiliary control mode or Key/AUX delegation mode is on.
d) Cross-point buttons of the bus assigned by AUX delegation setting.
e) In the case of an event that inserts or deletes a key by an independent key
transition, the key state at the time of event registration (inserted or not
inserted) is also saved in the macro. When the macro is executed, the event
is only replayed if the key state matches the saved state. (Example: For a
macro with an event that deletes a key, when the macro is executed, if the
key is inserted it is deleted, but otherwise nothing occurs as concerns
keying.)
f) When there are a number of control blocks on the control panel, and the
keys assigned to them in setup are the same, then the macro attachment
settings for the above buttons are the same.
The keys include cases such as “Key1,2” assigned to PGM/PST being the
same as “DSK1,2”, “Key1,2” assigned to M/E-1 being the same as “M/E-
1 Key1,2”, and so on.
g) KEY5 to KEY8 and DSK5 to DSK8 require an assignment.
Notes
• After setting a macro attachment to a cross-point button
in the auxiliary bus control block, if in the Setup menu
you change the assignment of buses to the AUX
delegation buttons, the macro attachment setting
disappears.
• After setting a macro attachment to a button for which
you can perform function replacement or function
assignment, if you change the function assignment to the
button, the macro attachment setting disappears.
• After setting a macro attachment to a cross-point button
in the cross-point control block, if you change the
function assignment to the button, the macro attachment
setting disappears.
Enabling and disabling macro attachment
You can temporarily disable the macro attachment
settings. When a macro attachment is disabled, pressing
the button does not cause execution of the assigned macro.