Sony MVS-8000X SystemMVS-7000X System - Page 619

USO RESTRITO
Signal Output Settings (Output Menu) 619
Chapter
20
Switcher
Setup
(Switcher)
• Press the arrow keys to scroll the reverse video cursor.
• Turn the knob.
Knob
Parameter
Adjustment
Setting values
1
Output No
Output connector
number selection
1 to 48
The selected output signal appears in reverse video.
Adjusting the video clip
To adjust the clip value for each of the output signals from
the Output 1 to 48 connectors, use the following
procedure.
1 In the Switcher >Output menu, press [Video Clip].
The Video Clip menu appears.
The status area shows the output connectors and
assigned signals, and the white clip, dark clip, and
chrominance clip values.
2 Adjust the following parameters.
Knob
Parameter
Adjustment
Setting values
2
White Clip
Luminance
signal white clip
value
90.00 to 109.02
3
Dark Clip
Luminance
signal dark clip
value
–6.85 to +10.00
4
Chroma
Clip
Chrominance
signal clip value
90.00 to 113.17
To set the values to the default values, press [Default].
Making vertical blanking interval
adjustment and through mode settings
1 In the Switcher >Output menu, press [V Blank/
Through].
The V Blank/Through menu appears.
The status area shows the output connectors and the
assigned signals, the vertical blanking interval, and the
through mode Enable/Disable status.
2 Press [V Blank Mask].
3 Adjust the parameter.
Knob
Parameter
Adjustment
Setting values
2
Mask End
Final value for
vertical blanking
interval
See note a)
below
a) Depending on the signal format, the adjustment range varies as
follows.
480i: 10 to 19
576i: 6 to 22
1080i/1080PsF: 7 to 20
720P: 7 to 25
1080P: 15 to 41
To return the values to their defaults, press [Default].
4 To enable the through mode, press [Through Mode],
setting it to Enable.
The through mode can be applied to the following
outputs.
• Aux 1 to 48 outputs
• Program outputs of the M/E and PGM/PST rows
• Clean outputs of the M/E and PGM/PST rows
Making safe title settings
1 In the Switcher >Output menu, press [Safe Title].
The Safe Title menu appears.
The status area shows the output connectors and the
assigned signals, with the box 1, box 2, cross, and grid
states.
2 To enable the safe title on/off setting made in the Misc
menu, press [Safe Title], turning it on.
3 Carry out either of the following operations.
To display a box: Press [Box1] or [Box2], turning it
on.
In this case, carry out the following steps 4 and 5.
To display a cross: Press [Cross], turning it on.
To display a grid: Press [Grid], turning it on.
In this case, carry out the following steps 4 and 5.
4 When you selected [Box1] or [Box2] in step 3, adjust the
following parameters.
Knob
Parameter
Adjustment
Setting values
2
Box Size
Box size
50.00 to 100.00
3
Luminance
Display
brightness
0.00 to
100.00
a)
a) Adjustable for Box2
When in step 3 you selected [Grid], in the <Grid Size> group, select one of the following.
80.00%: Set the grid size to 80% of the screen frame
85.00%: Set the grid size to 85% of the screen frame
90.00%: Set the grid size to 90% of the screen frame
100.00%: Set the grid size to the full-screen size
(100% of the screen frame)
5 When in step 3 you selected [Box1] or [Box2], in the
<Box1 Adjust> or <Box2 Adjust> group, select the
screen aspect ratio (16:9/14:9/4:3).
When in step 3 you selected [Grid], in the <Grid
Adjust> group, select the screen aspect ratio (16:9/
4:3).