Edge-Core ECS4610-24F User Manual

Name: Edge-Core ECS4610-24F
Brand: Edge-Core
Rating: 4 (1 reviews)

1154 pages

To Next Page

To Previous Page

HAPTER

| Security Measures

Access Control Lists

– 284 –

security reasons). A packet will also be denied if the IP ACL denies it

and the MAC ACL accepts it.

SETTING A TIME

RANGE

Use the Security > ACL (Configure Time Range) page to sets a time range

during which ACL functions are applied.

CLI REFERENCES

◆ "Time Range" on page 625

PARAMETERS

These parameters are displayed in the web interface:

Add

◆ Time-Range Name – Name of a time range. (Range: 1-30 characters)

Add Rule

◆ Time-Range – Name of a time range.

◆ Mode

■

Absolute – Specifies a specific time or time range.

■

Start/End – Specifies the hours, minutes, month, day, and year

at which to start or end.

■

Periodic – Specifies a periodic interval.

■

Start/To – Specifies the days of the week, hours, and minutes

at which to start or end.

WEB INTERFACE

To configure a time range:

1. Click Security, ACL.

2. Select Configure Time Range from the Step list.

3. Select Add from the Action list.

4. Enter the name of a time range.

5. Click Apply.

Other manuals for Edge-Core ECS4610-24F

Installation Guide78 pages

Questions and Answers:

M
Mrs. Diane FischerAug 7, 2025
What to do if I cannot connect to Edge-Core Switch using Secure Shell?
- S
  Shelby BeckAug 8, 2025
  If you're having trouble connecting to the Edge-Core Switch using Secure Shell, it could be due to several reasons. You might have exceeded the maximum number of concurrent Telnet/SSH sessions, so try connecting again later. Ensure that the control parameters for the SSH server are properly configured on the switch and that the SSH client software is correctly configured on your management station. Verify that you've generated both an RSA and DSA public key on the switch, exported this key to the SSH client, and enabled the SSH service. Also, make sure you've set up an account on the switch for each SSH user, including the username, authentication level, and password. If using public key authentication, confirm that you've imported the client's public key to the switch.
D
Dustin MooreAug 14, 2025
What to do if the Link LED is off on my Edge-Core ECS4610-24F?
- V
  Vernon GreeneAug 14, 2025
  If the Link LED is off on your Edge-Core Network Router, there are several potential causes and solutions: * First, ensure that both the switch and the connected device are powered on. * Next, make sure the cable is securely plugged into both the switch and the corresponding device. * If the switch is in a rack, inspect the connections to the punch-down block and patch panel. * Verify you're using the correct cable type and that its length is within specified limits. * Inspect the adapter on the attached device and the cable connections for any defects, replacing them if needed. * Finally, if an SFP transceiver has failed, replace it.

Edge-Core ECS4610-24F Specifications

General

Model	ECS4610-24F
Switching Capacity	128 Gbps
MAC Address Table Size	16K
Jumbo Frames	9K Bytes
Operating Humidity	10% to 90% (non-condensing)
Storage Humidity	5% to 95% (non-condensing)
Layer	L2/L3
Forwarding Rate	95.2 Mpps
VLANs	4K
Management	Web, CLI, SNMP
Power Supply	Internal
Dimensions (W x D x H)	440 x 44 x mm
Operating Temperature	0°C
Storage Temperature	-40°C to 70°C
Ports	24 x 1G SFP ports, 4 x 10G SFP+ ports