2 - 31
Chapter 2 Troubleshooting
093
952
C - CRUM Error
Error 093-952
Restart Printer
<IOT Cyan Toner CRUM Comm Fail>
The Cyan Toner Cartridge CRUM communication failure
is detected.
FIP-1.93
960
Invalid Toner
Yellow
<IOT (Y) CRUM ID Error>
An unsupported Toner Cartridge (Y) is detected.
FIP-1.94
961
Invalid Toner
Magenta
<IOT (M) CRUM ID Error>
An unsupported Toner Cartridge (M) is detected.
FIP-1.94
962
Invalid Toner
Cyan
<IOT (C) CRUM ID Error>
An unsupported Toner Cartridge (C) is detected.
FIP-1.94
970
Insert Yellow
Toner Cartridge
<IOT Toner Cartridge (Y) Detached>
The Toner Cartridge (Y) is not installed in the printer. If no
toner cartridge has been installed in the printer, a warning
is indicated on the LCD panel in the following order:
1)Black ï‚® 2)Cyan ï‚® 3)Magenta ï‚® 4)Yellow
FIP-1.96
971
Insert Magenta
Toner Cartridge
<IOT Toner Cartridge (M) Detached>
The Toner Cartridge (M) is not installed in the printer. If no
toner cartridge has been installed in the printer, a warning
is indicated on the LCD panel in the following order:
1)Black ï‚® 2)Cyan ï‚® 3)Magenta ï‚® 4)Yellow
FIP-1.96
972
Insert Cyan
Toner Cartridge
<IOT Toner Cartridge (C) Detached>
The Toner Cartridge (C) is not installed in the printer. If no
toner cartridge has been installed in the printer, a warning
is indicated on the LCD panel in the following order:
1)Black ï‚® 2)Cyan ï‚® 3)Magenta ï‚® 4)Yellow
FIP-1.96
973
Insert Black
Toner Cartridge
<IOT Toner Cartridge (K) Detached>
The Toner Cartridge (K) is not installed in the printer. If no
toner cartridge has been installed in the printer, a warning
is indicated on the LCD panel in the following order:
1)Black ï‚® 2)Cyan ï‚® 3)Magenta ï‚® 4)Yellow
FIP-1.96
094
422
Ready to Print
Replace Transfer
Unit Soon.
Life Almost Over.
<IOT Belt Unit Near Life>
The Belt Unit has reached the replacement time.
FIP-1.97
911
Replace
Transfer Unit
<IOT Belt Unit Life Over>
The Belt Unit has reached the replacement time.
FIP-1.98
116
210
USB Host Error
Error 116-210
Restart Printer
<USB Host Error>
Fatal error of USB Host driver
FIP-1.8
315
RAM Error
Error 116-315
Restart Printer
<ESS On Board RAM R/W Check Fail>
An error occurred during the onboard
RAM read/write check at the time of initialization.
FIP-1.8
This code is given when the Optional 512MB Memory is installed.
316
RAM Error
Error 116-316
Restart Printer
<ESS DIMM Slot RAM R/W Check Fail>
Unsupported additional memory module is detected in the
memory slot.
FIP-1.99
317
Controller Error
Error 116-317
Restart Printer
<ESS ROM Check (Main) Fail>
Checksum error occurred in the main program ROM.
FIP-1.8
This code is given when the Optional 512MB Memory is installed.
320
RAM Error
Error 116-320
Restart Printer
<ESS DIMM Slot RAM Error>
Additional memory module is not completely inserted in
the slot.
FIP-1.99
Status
Code
Error Message
Status Contents
FIP to be
referred
LCD
To Next Page
Loading...
Need help?
General
