6 – 52
Chapter 6 General
821-403
Auto Reduction
RECEIVE_REDUCTION
0: Page feed
1: Discard without page
feed
2: Auto reduce
0USER
821-406
Max amount of 1-page data in
color receiving
COLOR_RX_PAGE_LIMIT
0
～
64:0
～
4MB
(1step=64KB)
16 CE
821-407 Duplex Print Setting DUPLEX_PRINT_ENABLE
0:OFF
1:ON
0USER
821-411 Auto output of Activity Report AUTO_LOG_PRINT
0:OFF
1:ON
1USER
821-412
Page Margin
(Reduction: ON)
PAGE_MARGIN_REDUCTION
0
～
127:0mm
～
127mm
30 CE
825-002 Line Type LINE_TYPE
0:PSTN
1:PBX
0USER
825-004
Time before the switching of the
relay at pulse dialing (Waiting
time until the line stabilizes)
DP_RELAY_DELAY
0
～
255:0ms
～
2550ms
10ms/step
1
Time before switching to PB by
"
：
" during pulse dialing. Waits
for this system-data-specified
length of time after dial pulses,
before sending out PB.
CE
825-005 Permit/Prohibit DRPD Setting DRPD_ENABLE
0: Prohibit
1: Permit
1 DISTINCTIVE RING setting USER
825-006 DRPD Setting DRPD_SETTING
0:reserve
1:pattern1
2:pattern2
3:pattern3
4:pattern4
5:pattern5
6:pattern6
7:pattern7
4
For details, see "FAX Auto
Switching" in FAX functional
specifications.
USER
825-013 20PPS Pulse Dial DIS_DP_20PPS
0: DP20 permitted
1: DP20 prohibited
1
If Prohibited is selected, the MC
operates using 10PPS even if
20PPS is selected in
"DIAL_TYPE".
CE
825-014 Auto Receive Switching Mode AUTO_ANSWER_SELECT
0:Tel only
1:FAX only
2:TEL/FAX
3:ANS/FAX
4:DRPD
1USER
825-015 CNG Detection Time CNG_DETECT_TIME
0
～
255:0s
～
25.5s
165 CE
825-016
External Telephone Access
Time
(Time during which the speaker
keeps ringing if CNG cannot be
detected after call-in)
AUTO_ANSWER_TIME
0
～
255:0s
～
255s
21 CE
825-017
External Telephone Access
Time in TEL/FAX Switching
Mode
AUTO_ANSWER_TIME_TELFAX
0
～
255:0s
～
255s
--The setting range below
applies to New Zealand
only.
3
～
255
：
3s
～
255s
6USER
825-018
External Telephone Access
Time in Answering Machine
Connected Mode
AUTO_ANSWER_TIME_RUSU
0
～
255:0s
～
255s
-- The setting range below
applies to New Zealand
only.
3
～
255
：
3s
～
255s
21 USER
825-019 Access time in FAX Mode only AUTO_ANSWER_DELAY
0
～
255:0s
～
255s
-- The setting range below
applies to New Zealand
only.
3
～
25
：
3s
～
25s
0USER
825-025
(14/0.5) Ring Signal Cycle:
Min. Value
RING_CYCLE_MIN
8
～
255:4ms
～
127.5ms
28
Ring Signal Detectable Cycle
setting
（
1step=0.5ms)
CE
825-026
(100/0.5) Ring Signal Cycle:
Max. Value
RING_CYCLE_MAX
8
～
255:4ms
～
127.5ms
200
Ring Signal Detectable Cycle
setting
（
1step=0.5ms
）
CE
825-027 Dial Tone Frequency SELECT_DIALTONE
0:350Hz
～
450Hz
1:300Hz
～
500Hz
2:450Hz
～
650Hz
3:245Hz
～
650Hz
3
Dial Tone Detectable Frequency
setting
Not used.
CE
Chain
-Link
Description Name Value Label
Default
Details Access
OFF/
ON
To Next Page
Loading...
