Sony MVS-8000X SystemMVS-7000X System - Page 135

USO RESTRITO
Key Adjustments (Menus) 135
Knob
Parameter
Adjustment
Setting values
1
Width
Width
a)
2
Position
Position
359.99 to 0.00
3
Density
Density
0.00 to 100.00
Knob
Parameter
Adjustment
Setting values
1
Width
Width
0.00 to 4.00
2
Position
Position
359.99 to 0.00
3
Density
a)
Density
0.00 to 100.00
Knob
Parameter
Adjustment
Setting values
1
Luminance
Luminance
0.00 to 100.00
2
Saturation
Saturation
0.00 to 100.00
3
Hue
Hue
359.99 to 0.00
Knob
Parameter
Adjustment
Setting values
1
Top
Key top edge
position
–2.00 to +2.00
2
Left
Key left edge
position
–2.00 to +2.00
3
Right
Key right edge
position
–2.00 to +2.00
4
Bottom
Key bottom
edge position
–2.00 to +2.00
Chapter
4
Keys
When drop border or shadow is selected: The
setting parameter values depend on the on/off
setting of key drop and the selection of 4H mode/
8H mode (see page 125).
• “Key drop off” mode
Knob
Parameter
Adjustment
Setting values
1
Width
Width
0.00 to 8.00
a)
2
Position
Position
359.99 to
180.00
3
Density
Density
0.00 to 100.00
• “Key drop on” mode
Notes
To enable the [UTIL] button, its operation mode
must be set to [Hold] beforehand.
For details, see “Setting the Button Operation
Mode” in Chapter 19 (Volume 2).
When [Matte] is selected: Press [Matte Adjust] in the
same EDGE menu, to display the Matte Adjust
menu, and adjust a single color or two-color
combination color matte.
You can select whether to use a single color matte
or a two-color combination color matte in the
<Edge Matte> group.
0.00 to 8.00
a) In the “4H mode” and when [Fine Key] (page 135) is on, the setting
value range is 0.00 to 4.00.
When emboss is selected:
For the color mix operation, see “Carrying out a color
mix for the key edge fill matte” (page 136).
6 When emboss is selected for the edge type, adjust the color in the <Emboss Fill> group.
To adjust matte 1 press [Matte1], and to adjust matte 2
press [Matte2], then adjust the following parameters.
Knob
Parameter
Adjustment
Setting values
1
Luminance
Luminance
0.00 to 100.00
2
Saturation
Saturation
0.00 to 100.00
3
Hue
Hue
359.99 to 0.00
a) The Density adjustment only affects the key edge. This can be
adjusted separately from Key Density, and if Key Density is set to
0.00, the embossed edge effect only can be applied.
To make edge fill adjustments, carry out the settings in
step 6.
4 Select the edge fill signal in the <Edge Fill> group.
Utility 1 Bus: signal selected on the utility 1 bus
Matte: signal from dedicated color matte generator.
It becomes possible to adjust color 1.
7 To make the edge soft, press [Soft Edge] to set it on,
and adjust the softness.
Knob
Parameter
Adjustment
Setting values
1
Soft
Edge softness
0.00 to 100.00
For a normal edge, when [Soft Edge] is enabled, [Key
Drop] is kept on.
8 To make separate fine adjustments to the positions of
the left, right, top, and bottom of the source edge, press
[Fine Key], to set it on, and adjust the following
parameters.
Parameter group [1/2]
When the edge type is outline, in place of the edge fill
signal, the selected key fill signal fills the outline, and
elsewhere remains as the background.
5 Carry out the following operation, depending on the
selection in step 4.
When [Utility 1 Bus] is selected: Hold down the
[UTIL] button in the cross-point control block,
and select the signal in the background A bus row.
While the [UTIL] button is held down, the
background A bus changes to the utility 1 bus.