Siemens SINUMERIK 828D Turning - Page 14

Table of contents
Turning
14 Operating Manual, 03/2013, 6FC5398-8CP40-3BA1
8.1.1 General...................................................................................................................................... 277
8.1.2 Centering (CYCLE81) ...............................................................................................................
278
8.1.3 Drilling (CYCLE82)....................................................................................................................
281
8.1.4 Reaming (CYCLE85) ................................................................................................................
283
8.1.5 Boring (CYCLE86) ....................................................................................................................
285
8.1.6 Deep-hole drilling (CYCLE83)...................................................................................................
289
8.1.7 Tapping (CYCLE84, 840)..........................................................................................................
293
8.1.8 Drill and thread milling (CYCLE78) ...........................................................................................
299
8.1.9 Positions and position patterns .................................................................................................
303
8.1.9.1 Approach/retraction...................................................................................................................
303
8.1.10 Arbitrary positions (CYCLE802)................................................................................................
304
8.1.10.1 Function.....................................................................................................................................
304
8.1.11 Position pattern line (HOLES1), grid or frame (CYCLE801).....................................................
307
8.1.12 Circle position pattern (HOLES2)..............................................................................................
309
8.1.13 Displaying and hiding positions.................................................................................................
313
8.1.14 Repeating positions...................................................................................................................
315
8.1.14.1 Function.....................................................................................................................................
315
8.2 Rotate........................................................................................................................................
316
8.2.1 General......................................................................................................................................
316
8.2.2 Stock removal (CYCLE951)......................................................................................................
316
8.2.3 Groove (CYCLE930).................................................................................................................
319
8.2.4 Undercut form E and F (CYCLE940) ........................................................................................
322
8.2.5 Thread undercuts (CYCLE940) ................................................................................................
324
8.2.6 Thread turning (CYCLE99) .......................................................................................................
327
8.2.7 Thread chain (CYCLE98)..........................................................................................................
336
8.2.7.1 Parameters................................................................................................................................
338
8.2.8 Cut-off (CYCLE92) ....................................................................................................................
340
8.3 Contour turning .........................................................................................................................
342
8.3.1 General information...................................................................................................................
342
8.3.2 Representation of the contour...................................................................................................
343
8.3.3 Creating a new contour.............................................................................................................
345
8.3.4 Creating contour elements........................................................................................................
347
8.3.5 Entering the master dimension .................................................................................................
352
8.3.6 Changing the contour................................................................................................................
354
8.3.7 Contour call (CYCLE62) - only for G code program .................................................................
355
8.3.8 Stock removal (CYCLE952)......................................................................................................
356
8.3.9 Stock removal rest (CYCLE952)...............................................................................................
362
8.3.10 Plunge-cutting (CYCLE952)......................................................................................................
365
8.3.11 Plunge-cutting rest (CYCLE952)...............................................................................................
368
8.3.12 Plunge-turning (CYCLE952) .....................................................................................................
370
8.3.13 Plunge-turning rest (CYCLE952) ..............................................................................................
374
8.4 Milling ........................................................................................................................................
377
8.4.1 Face milling (CYCLE61)............................................................................................................
377
8.4.2 Rectangular pocket (POCKET3)...............................................................................................
381
8.4.3 Circular pocket (POCKET4)......................................................................................................
387
8.4.4 Rectangular spigot (CYCLE76).................................................................................................
393
8.4.5 Circular spigot (CYCLE77)........................................................................................................
397
8.4.6 Multi-edge (CYCLE79)..............................................................................................................
401
8.4.7 Longitudinal groove (SLOT1)....................................................................................................
404
8.4.8 Circumferential groove (SLOT2) ...............................................................................................
410
8.4.9 Open groove (CYCLE899)........................................................................................................
415