Table of contents
Turning
Operating Manual, 03/2013, 6FC5398-8CP40-3BA1
15
8.4.10 Long hole (LONGHOLE) - only for G code program..................................................................424
8.4.11 Thread milling (CYCLE70).........................................................................................................
426
8.4.12 Engraving (CYCLE60) ...............................................................................................................
430
8.5 Contour milling ...........................................................................................................................
437
8.5.1 General information ...................................................................................................................
437
8.5.2 Representation of the contour....................................................................................................
437
8.5.3 Creating a new contour..............................................................................................................
439
8.5.4 Creating contour elements.........................................................................................................
441
8.5.5 Changing the contour.................................................................................................................
447
8.5.6 Contour call (CYCLE62) - only for G code program ..................................................................
448
8.5.7 Path milling (CYCLE72) .............................................................................................................
449
8.5.8 Contour pocket/contour spigot (CYCLE63/64) ..........................................................................
454
8.5.9 Predrilling contour pocket (CYCLE64).......................................................................................
456
8.5.10 Milling contour pocket (CYCLE63).............................................................................................
461
8.5.11 Contour pocket residual material (CYCLE63, option)................................................................
464
8.5.12 Milling contour spigot (CYCLE63)..............................................................................................
467
8.5.13 Contour spigot residual material (CYCLE63, option).................................................................
470
8.6 Further cycles and functions ......................................................................................................
473
8.6.1 Swiveling plane / aligning tool (CYCLE800) ..............................................................................
473
8.6.2 Swiveling tool (CYCLE800)........................................................................................................
482
8.6.2.1 Aligning turning tools - only for G code program (CYCLE800)..................................................
482
8.6.2.2 Aligning milling tools - only for G code program (CYCLE800)...................................................
483
8.6.2.3 Preloading milling tools - only for G code program (CYCLE800) ..............................................
484
8.6.3 High-speed settings (CYCLE832)..............................................................................................
486
8.6.4 Subroutines................................................................................................................................
489
8.7 Additional cycles and functions in ShopTurn.............................................................................
491
8.7.1 Drilling centric.............................................................................................................................
491
8.7.2 Thread centered.........................................................................................................................
493
8.7.3 Transformations .........................................................................................................................
496
8.7.4 Translation .................................................................................................................................
498
8.7.5 Rotation......................................................................................................................................
499
8.7.6 Scaling .......................................................................................................................................
500
8.7.7 Mirroring.....................................................................................................................................
501
8.7.8 Rotation C ..................................................................................................................................
502
8.7.9 Straight and circular machining..................................................................................................
503
8.7.10 Selecting a tool and machining plane ........................................................................................
504
8.7.11 Programming a straight line .......................................................................................................
505
8.7.12 Programming a circle with known center point ..........................................................................
507
8.7.13 Programming a circle with known radius ...................................................................................
509
8.7.14 Polar coordinates .......................................................................................................................
511
8.7.15 Straight line polar .......................................................................................................................
513
8.7.16 Circle polar.................................................................................................................................
515
8.7.17 Machining with movable counterspindle ....................................................................................
517
8.7.17.1 Programming example: Machining main spindle – Transfer workpiece – Machining
counterspindle............................................................................................................................
518
8.7.17.2 Programming example: Machining, counterspindle - without previous transfer ........................
518
8.7.17.3 Programming example: Machining bar material ........................................................................
519
8.7.18 Machining with fixed counterspindle ..........................................................................................
524
To Next Page
Loading...
Need help?
General
