Sony MVS-8000X SystemMVS-7000X System - Page 168

USO RESTRITO
168
Basic Procedure for Wipe Settings
Knob
Parameter
Adjustment
Setting values
1
Width
Border width
0.00 to 100.00
Knob
Parameter
Adjustment
Setting values
1
Soft
Edge softness
0.00 to 100.00
Knob
Parameter
Adjustment
Setting values
1
Width
Border width
0.00 to 100.00
2
Inner Soft
Border inner
softness
0.00 to 100.00
3
Outer Soft
Border outer
softness
0.00 to 100.00
Knob
Parameter
Adjustment
Setting values
1
Size
Pattern size
0.00 to 100.00
Chapter
5
Wipes
Border: border
Soft: soft edge
Soft Border: soft border
3 Set the parameters according to the selection in step 2.
When border is selected
When soft edge is selected
When soft border is selected
4 When you selected border or soft border, select the
edge fill signal in the <Edge Fill> group.
Utility 2 Bus: signal selected on the utility 2 bus
Matte: signal from the dedicated color matte
generator
5 Depending on the operation in step 4, carry out the
following operation.
When ‘Utility 2 Bus’ is selected: Hold down the
[UTIL] button in the cross-point control block,
and select the signal on the background B bus.
While the [UTIL] button is held down, the
background B bus changes to the utility 2 bus.
Notes
To enable the [UTIL] button, its operation mode
must be set to [Hold] beforehand.
For details, see “Setting the Button Operation
Mode” in Chapter 19 (Volume 2).
When ‘Matte’ is selected: In the same Edge/
Direction menu, press [Matte Adjust] to display
the Matte Adjust menu, then adjust the single-
color or two-color combination color matte. Select
whether to use a single-color matte or a two-color
combination in the <Edge Matte> group.
Flat Color: Adjust color 1 with the following
parameters.
Knob
Parameter
Adjustment
Setting values
2
Saturation
Saturation
0.00 to 100.00
3
Hue
Hue
359.99 to 0.00
When you select [Mix Color] for a two-color
combination, see the next paragraph.
Carrying out a color mix for the edge fill
matte
When you selected [Matte] for the border or soft border
edge fill, you can combine color 1 and color 2.
For the combination, you can use not only a normal wipe
generator pattern, but also the dedicated color mix pattern.
1 In the <Edge Fill> group of the Edge/Direction menu,
select [Matte], and press [Matte Adjust].
The Matte Adjust menu appears.
2 In the <Edge Matte> group, select [Mix Color],
turning it on.
3 In the <Mix Pattern> group, make one of the following
selections.
Wipe: Use the wipe pattern selected for the transition.
Pattern: Use the dedicated pattern.
4 Depending on the selection in step 3, set the following
parameters.
When Wipe is selected
Knob
Parameter
Adjustment
Setting values
1
Size
Pattern size
0.00 to 100.00
2
Soft
Edge softness
0.00 to 100.00
When Pattern is selected
Knob
Parameter
Adjustment
Setting values
1
Size
Pattern size
0.00 to 100.00
2
Soft
Edge softness
0.00 to 100.00
3
Pattern
Pattern number
1 to 24
a)
a) The patterns are the same as for a standard wipe. See “Wipe Pattern
List” (page 357) in Appendix.
If you selected Pattern, you can also carry out the
pattern selection by pressing [Mix Pattern Select] in
the Matte Adjust menu, to display the Mix Ptn Select
menu. Select any pattern appearing in the Mix Ptn
Select menu (wipe patterns 1 to 24) by pressing the
appropriate button, and you can then adjust the
following parameters.
Knob
Parameter
Adjustment
Setting values
1
Luminance
Luminance
0.00 to 100.00