FOR-A FA-9520 - GPI Output Circuit

To Next Page

To Previous Page

241

14-4. GPI Output Circuit

IMPORTANT

Note that the allowed current for each GPI output circuit is 10mA and the external

power supply should be 5VDC.

+5.4V

Select external or internal

power.

PIN 9

PINs 2-8

PIN 1

5VDC

(external power)

Protective resistor

FA-9520 inside

Main Page

Default Chapter7
- Table of Contents7
1 Prior to Starting15
- Welcome15
- Features15
- FA-95LG GUI Download15
2 Panel Descriptions16
- Front Panel16
- Rear Panel18
- Internal Settings21
  - Dipswitch Settings21
3 Connections22
- For 2-Channel Frame Synchronizer Use22
- For HD/SD-SDI Simul Output23
- To Embed AES Input Signals on SDI Signals24
- To Embed Analog Audio Signals on SDI Signals25
- Connecting a Computer26
- Connecting to the REMOTE (GPI) Connector27
4 Front Panel Operation28
- Powering on28
- Basic Operation28
5 VIDEO Menus37
- Video Proc Amp (Process)37
- Color Corrector (C.C.)37
- Conv (Up/Down/Cross Converter)40
- Auto Video Optimizer (AVO)46
- Clip (Video Clip)54
- Video Input Select (in Sel)57
- Video out Select (out Sel)61
- Video Option (Video Op)67
  - Logo Generator67
- Video System (Video Sys)69
- Various Signal Status Display (STATUS)81
6 AUDIO Settings98
- SDI AUDIO Settings (SDI AUDIO)98
- AES AUDIO Settings (AES AUDIO)104
- ANALOG AUDIO Settings (ANALOG)106
- Output Gain Control108
- Audio Mapping (Mapping)111
- AUDIO DELAY Settings115
- Down Mix1 Set117
  - Down Mix1 Assign118
- Down Mix2 Set119
  - Down Mix2 Assign120
- Audio Mode Set (Mode)121
- Audio Option (Audio Op)125
  - Fa-95D-D / Fa-95De-E125
  - Automatic Loudness Adjustment (FA-95ALA)132
- AUDIO SYSTEM Settings (AUDIO SYS)137
7 Other Settings & Information (OTHER)141
- Fs1/Fs2 Copy141
- Mu Operation142
  - Important Note on Changing the Operation Mode142
  - FA-9520 Operation Mode Change Procedure142
- Control Setting143
- Front Operation143
- Front Panel Set143
- Gpi Setting144
- Network Info147
- UNIT Ver147
- OPTION a Ver148
- OPTION B Ver148
- Other Option149
- Soft Option1149
- Soft Option2149
8 Event Memory150
- Event Load150
- Event Save151
- Event Setup151
- Parameters Not Stored in Event Memory151
- Note on Event Memory Operation151
9 Control Via WEB Browser152
- Connecting Via a WEB Browser152
- VIDEO Settings153
- AUDIO Settings176
- SYSTEM Settings200
- Gpi213
- Utility Settings215
- Status Display220
- Network Settings229
10 Downmix Block Diagram234
11 ANALOG/DIGITAL Audio Input/Output Level235
- Analog Output Level Relative to the Digital Input Level235
- Digital Output Level Relative to the Analog Input Level236
12 Analog Audio Connection237
13 Dolby E Decoder/Encoder Channel Assignment Table238
14 Remote239
- REMOTE Connector239
- GPI Input Circuit239
- GPI Input Control240
- GPI Output Circuit241
15 How to Install the FA-95DACBL242
- Procedure242
- Installation Confirmation243
16 FA-95AIO Option244
- FA-95AIO Pin Assignments244
- FA-95AIO Switch Settings245
17 System Requirements245
18 About SNMP (Simple Network Management Protocol)246
19 FA-9520 Ancillary Data Packet Name List259
20 About AFD (Active Format Description)261
- AFD Codes262
- Aspect Ratio Conversion with AFD264
- AFD Supported Video Formats268
- AFD Based Auto Aspect Conversion Settings268
- How to Insert AFD Data to Output Video Signals269
- AFD Code Abbreviations270
21 About Closed Captioning272
- Closed Captioning Setting Procedure272
22 Verification after Option Card Removal/Replacement273
- Alert273
- Verification after Dolby Option Removal/Replacement273
- Verification after FA-95AIO Removal/Replacement273
- Verification after FA-95ALA Removal/Replacement274
23 Expansion Slots a / B Alert274
24 Specifications and Dimensions275
- Unit Specifications275

FOR-A FA-9520 - GPI Output Circuit

Table of Contents

Other manuals for FOR-A FA-9520

Related product manuals