Siemens SINAMICS G120 - Page 482

Parameters
Connector/Binector (BICO)-Parameters
1-482
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
r2120 CO: Sum of fault and alarm buffer changes / Sum buffer changed
r2121 CO: Counter, alarm buffer changes / Alrm buff changed
r2131 CO: Actual fault code / Actual fault code
r2132 CO: Actual alarm code / Actual alarm code
r2169 CO: Actual speed smoothed signals / n_act smth message
p2201[0...n] CO: Technology controller, fixed value 1 / Tec_ctr fix val 1
p2202[0...n] CO: Technology controller, fixed value 2 / Tec_ctr fix val 2
p2203[0...n] CO: Technology controller, fixed value 3 / Tec_ctr fix val 3
p2204[0...n] CO: Technology controller, fixed value 4 / Tec_ctr fix val 4
p2205[0...n] CO: Technology controller, fixed value 5 / Tec_ctr fix val 5
p2206[0...n] CO: Technology controller, fixed value 6 / Tec_ctr fix val 6
p2207[0...n] CO: Technology controller, fixed value 7 / Tec_ctr fix val 7
p2208[0...n] CO: Technology controller, fixed value 8 / Tec_ctr fix val 8
p2209[0...n] CO: Technology controller, fixed value 9 / Tec_ctr fix val 9
p2210[0...n] CO: Technology controller, fixed value 10 / Tec_ctr fix val 10
p2211[0...n] CO: Technology controller, fixed value 11 / Tec_ctr fix val 11
p2212[0...n] CO: Technology controller, fixed value 12 / Tec_ctr fix val 12
p2213[0...n] CO: Technology controller, fixed value 13 / Tec_ctr fix val 13
p2214[0...n] CO: Technology controller, fixed value 14 / Tec_ctr fix val 14
p2215[0...n] CO: Technology controller, fixed value 15 / Tec_ctr fix val 15
r2224 CO: Technology controller, fixed value effective / Tec_ctr FixVal eff
r2245 CO: Technology controller mot. potentiometer setpoint before RFG / Tec_ctr mop befRFG
r2250 CO: Technology controller motorized potentiometer setpoint after RFG / Tec_ctr mop aftRFG
r2260 CO: Technology controller setpoint after ramp-function generator / Tec_ctr set aftRFG
r2262 CO: Technology controller setpoint after filter / Tec_ctr set aftFlt
r2266 CO: Technology controller actual value after filter / Tec_ctr act aftFlt
r2272 CO: Technology controller actual value scaled / Tech_ctrl act scal
r2273 CO: Technology controller error / Tec_ctrl error
p2291 CO: Technology controller maximum limiting / Tec_ctrl max_limit
p2292 CO: Technology controller minimum limiting / Tec_ctrl min_lim
r2294 CO: Technology controller output signal / Tec_ctrl outp_sig
p2295 CO: Technology controller output scaling / Tec_ctrl outp scal
r2344 CO: Technology controller last speed setpoint (smoothed) / Tec_ctrl n_setp_sm
p2900[0...n] CO: Fixed value 1 [%] / Fixed value 1 [%]
p2901[0...n] CO: Fixed value 2 [%] / Fixed value 2 [%]
r2902[0...14] CO: Fixed values [%] / Fixed values [%]
p2930[0...n] CO: Fixed value M [Nm] / Fixed value M [Nm]
r3131 CO: Current flt value / Current flt value
r3132 CO: Actual component number / Act comp_no.
r9733[0...2] CO: SI Motion setpoint speed limit effective / SI Mtn setp_lim
r20095 CO: ADD 0 output Y / ADD 0 output Y
r20099 CO: ADD 1 output Y / ADD 1 output Y
r20103 CO: SUB 0 difference Y / SUB 0 difference Y
r20107 CO: SUB 1 difference Y / SUB 1 difference Y
r20111 CO: MUL 0 product Y / MUL 0 product Y
r20115 CO: MUL 1 product Y / MUL 1 product Y
r20119[0...2] CO: DIV 0 quotient / DIV 0 quotient
r20124[0...2] CO: DIV 1 quotient / DIV 1 quotient
r20129 CO: AVA 0 output Y / AVA 0 output Y
r20134 CO: AVA 1 output Y / AVA 1 output Y
r20220 CO: NSW 0 output Y / NSW 0 output Y
r20225 CO: NSW 1 output Y / NSW 1 output Y
r20231 CO: LIM 0 output Y / LIM 0 output Y