Siemens SINAMICS G120 - Page 745

Index
C-745
© Siemens AG 2011 All Rights Reserved
SINAMICS G120 / Control Units CU240B/E-2 Parameter Manual (LH11), 01/2011
Function diagrams Braking control
Basic braking control, 2-558
Function diagrams Data sets
Command Data Sets (CDS), 2-650
Drive Data Sets (DDS), 2-651
Function diagrams Faults and warnings
Fault buffer, 2-645
Fault/warning configuration, 2-648
Fault/warning trigger word (r2129), 2-647
Warning buffer, 2-646
Function diagrams Fieldbus Interface
Configuration, addresses and diagnostics,
2-519
Receive telegram, free interconnection via
BICO, 2-522
Send telegram, free interconnection via
BICO, 2-523
Status words, free interconnection, 2-524
STW1 control word interconnection,
2-520
ZSW1 status word interconnection, 2-521
Function diagrams Free Function Blocks
ADD (adder), 2-612
AND (AND function block with 4 inputs),
2-608
AVA (absolute value generators), 2-614
BSW (binary changeover switch), 2-622
DFR (D flipflop), 2-621
DIF (differentiating element), 2-625
DIV (divider), 2-613
INT (integrator), 2-625
LIM (limiter), 2-623
LVM (limit value monitor), 2-626
MFP (pulse generator), 2-617
MUL (multiplier), 2-613
NCM (numerical comparator), 2-615
NOT (inverter), 2-611
NSW (numerical changeover switch),
2-622
OR (OR function block with 4 inputs),
2-609
PCL (pulse shortener), 2-617
PDE (switch-in delay), 2-618
PDF (switch-out delay), 2-619
PLI (scaling polyline), 2-616
PST (pulse extender), 2-620
PT1 (smoothing element), 2-624
RSR (RS flipflop), 2-621
Run-time groups / Sampling times, 2-607
SUB (subtracter), 2-612
XOR (XOR function block with 4 inputs),
2-610
Function diagrams General
Explanation of the symbols (Part 1), 2-494
Explanation of the symbols (Part 2), 2-495
Explanation of the symbols (Part 3), 2-496
Handling BICO technology, 2-497
Function diagrams Input/Output Terminals
CU240B-2 Analog input 0 (AI0), 2-513
CU240B-2 Analog inputs as Digital inputs
(DI11), 2-509
CU240B-2 Analog output 0 (AO0), 2-515
CU240B-2 Digital inputs, electrically iso-
lated (DI0 ... DI3), 2-507
CU240B-2 Digital output (DO0), 2-511
CU240E-2 Analog inputs as Digital inputs
(DI11 ... DI12), 2-510
CU240E-2 Analog
inputs0...1(AI0...AI1), 2-514
CU240E-2 Analog outputs 0 ... 1
(AO0 ... AO1), 2-516
CU240E-2 Digital inputs, electrically iso-
lated (DI0 ... DI5), 2-508
CU240E-2 Digital outputs (DO0 ... DO2),
2-512
Function diagrams Internal control/status
words
Control word 1 (r0054), 2-545
Control word 2 (r0055), 2-546
Control word, faults/alarms, 2-554
Control word, sequence control, 2-540
Control word, setpoint channel, 2-542
Control word, speed controller, 2-547
Sequence control - Missing enable sig-
nals, 2-556
Status word 1 (r0052), 2-543
Status word 2 (r0053), 2-544
Status word, closed-loop control, 2-549
Status word, current control, 2-550
Status word, faults/alarms 1 and 2, 2-555
Status word, monitoring functions 1,
2-551
Status word, monitoring functions 2,
2-552
Status word, monitoring functions 3,
2-553
Status word, sequence control, 2-541
Status word, speed controller, 2-548