EasyManuals Logo

Icom IC-7100 Advanced Instructions

Icom IC-7100
375 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #118 background imageLoading...
Page #118 background image
6
FUNCTIONS FOR TRANSMIT
6-13
Measuring SWR
The IC-7100 has a built-in circuit for measuring antenna
SWR— no external equipment or special adjustments
are necessary.
The IC-7100 can measure SWR two ways spot mea-
surement and plot measurement.
D Spot measurement
This function is convenient to use when measuring
SWR of the antenna to install or periodic check.
q If desired, push
TUNER/CALL
(L) once or twice to turn
OFF the antenna tuner.
If the antenna tuner is connected, and your want to mea-
sure SWR of the antenna itself, perform this step.
Select the desired frequency band. (p. 3-6) w
On the Mode selection screen, select the RTTY or e
RTTY-R mode. (p. 3-17)
If necessary, adjust the RF power to more than 30 W r
on the Mic gain/RF power adjustment display.
If your are operating in the 144 MHz band, adjust the RF
power to more than 20 W.
If your are operating in the 430 MHz band, adjust the RF
power to more than 15 W.
If your are operating in the 70 MHz band, adjust the RF
power to more than 20 W. (70 MHz band transmission is
available, depending on the transceiver version.)
q Push
MIC/RF PWR
(C) to open the MIC gain/RF
power adjustment display.
w Rotate [BANK] (L) to adjust the RF power.
e Push
MENU
(C) to close the display.
Before transmitting, monitor the operating fre-
quency to make sure transmitting won’t cause
interference to other stations on the same fre-
quency.
Touch the TX meter one or more times to select the t
SWR meter.
Hold down [PTT] on the microphone or switch ON y
the external TX switch to transmit.
Read the SWR on the SWR meter. u
If the SWR meter points 1.5 or less, the antenna is
matched .
Release [PTT] or Switch OFF the external TX switch i
to receive.
When the measured SWR is more than 1.5:1, adjust the
antenna to match with the transceiver.
L
eft
R
ight
C
enter
D
isplay
NOTE
This transceiver can measure SWR in the 144 MHz or
430 MHz bands.
Depending on the length of the connected coaxial
cable, or installation condition, the measurement may
be different from the actual SWR of the antenna in
these band.
The L, R, C or D in the
instructions indicate the
part of the controller.
L: Left side
R: Right side
C: Center bottom
D:
Display (Touch screen)
The best match is in this range.
(1.5 or less)
SWR meter
RTTY mode icon
Previous view

Table of Contents

Other manuals for Icom IC-7100

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Icom IC-7100 and is the answer not in the manual?

Icom IC-7100 Specifications

General IconGeneral
Supply13.8 V DC ±15%
Voltage13.8 V DC
Operating Temperature-10°C to +60°C
Frequency Coverage0.030-199.999 MHz, 400-470 MHz
ModesSSB, CW, AM, FM, DV
Output PowerHF/50MHz: 100W, 144MHz: 50W, 430MHz: 35W
Receiver TypeSuperheterodyne
Antenna ConnectorSO-239 (HF/50MHz/144MHz), N-type (430MHz)
WeightMain unit: 2.3 kg
TypeBase/Mobile
Frequency Range TX1.8–54 MHz, 144–148 MHz, 430–450 MHz
Frequency Range RX0.030–199.999 MHz, 400–470 MHz
Memories505
Current ConsumptionTX: 22 A, RX: 1.2 A

Related product manuals