EasyManuals Logo

Icom IC-7100 Advanced Instructions

Icom IC-7100
375 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #71 background imageLoading...
Page #71 background image
4
RECEIVE AND TRANSMIT
4-9
D Contest number Set mode
This mode is used to set the contest number, count up
trigger and Present number.
• Setting contents
q
In the CW mode, p
ush
MENU
(C) one or more times
to select the “M-2” screen (M-2 menu).
w Push [KEYER](D) to display the “KEYER SEND”
screen.
If the “KEYER” (Root) screen is displayed, skip step e.
Push e
MENU
(C) to display the “KEYER” screen.
Push [001]( r D) to enter the “KEYER 001” (Contest
Number Set) screen.
Touch the desired item to select. t
Touch the y desired option or rotate the Dial to change
the setting.
If desired, touch the item for 1 second to open the Default
set window, then select “Default” to reset to the default
setting.
Push u
MENU
(C) to return to the “KEYER” (Root)
screen.
Electronic keyer functions (Continued)
“KEYER” (Root) screen
• Contest number Set mode
Number Style (Default: Normal)
This item sets the numbering system used for contest
numbers— normal or short morse numbers.
Short morse numbers are also referred to as “cut”
numbers.
Normal: Does not use short morse numbers
190ANO: Sets 1 as A, 9 as N and 0 as O.
190ANT: Sets 1 as A, 9 as N and 0 as T.
90NO: Sets 9 as N and 0 as O.
90NT: Sets 9 as N and 0 as T.
Count Up Trigger (Default: M2)
Set the count-up trigger to one of four memory slots for
the contest number exchange. The count-up trigger al-
lows the contest number to automatically advance after
each complete number exchange is sent.
M1, M2, M3 or M4 can be set.
Present Number (Default: 001)
This item shows the current number for the count-up
trigger channel set above.
Touch [+] or [–]
(D) or rotate the Dial to change the
number.
Hold down the item for 1 second to display the default
set window, then touch “Default” to set the counter to
“001.
To the default setting
• Default set window
The L, R, C or D in the instructions indicate the
part of the controller.
L: Left side, R: Right side, C: Center bottom
D: Display (Touch screen)
Touch [001]
Touch the item
for 1 second.
Touch “Default.
Touch the item
( Example: Num-
ber Style)
Touch the option
( Example:
190
ANO)
Previous view

Table of Contents

Other manuals for Icom IC-7100

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Icom IC-7100 and is the answer not in the manual?

Icom IC-7100 Specifications

General IconGeneral
Supply13.8 V DC ±15%
Voltage13.8 V DC
Operating Temperature-10°C to +60°C
Frequency Coverage0.030-199.999 MHz, 400-470 MHz
ModesSSB, CW, AM, FM, DV
Output PowerHF/50MHz: 100W, 144MHz: 50W, 430MHz: 35W
Receiver TypeSuperheterodyne
Antenna ConnectorSO-239 (HF/50MHz/144MHz), N-type (430MHz)
WeightMain unit: 2.3 kg
TypeBase/Mobile
Frequency Range TX1.8–54 MHz, 144–148 MHz, 430–450 MHz
Frequency Range RX0.030–199.999 MHz, 400–470 MHz
Memories505
Current ConsumptionTX: 22 A, RX: 1.2 A

Related product manuals