EasyManua.ls Logo

Renesas RL78 Series - CAN Receive Rule Entry Register Jch (Gaflphj) (J = 0 to 15)

Renesas RL78 Series
1879 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
RL78/F13, F14 CHAPTER 18 CAN INTERFACE (RS-CAN LITE)
R01UH0368EJ0210 Rev.2.10 1314
Dec 10, 2015
18.3.23 CAN Receive Rule Entry Register jCH (GAFLPHj) (j = 0 to 15)
Address GAFLPH0L: F03AAH, GAFLPH0H: F03ABH GAFLPH1L: F03B6H, GAFLPH1H: F03B7H
GAFLPH2L: F03C2H, GAFLPH2H: F03C3H GAFLPH3L: F03CEH, GAFLPH3H: F03CFH
GAFLPH4L: F03DAH, GAFLPH4H: F03DBH GAFLPH5L: F03E6H, GAFLPH5H: F03E7H
GAFLPH6L: F03F2H, GAFLPH6H: F03F3H GAFLPH7L: F03FEH, GAFLPH7H: F03FFH
GAFLPH8L: F040AH, GAFLPH8H: F040BH GAFLPH9L: F0416H, GAFLPH9H: F0417H
GAFLPH10L: F0422H, GAFLPH10H: F0423H GAFLPH11L: F042EH, GAFLPH11H: F042FH
GAFLPH12L: F043AH, GAFLPH12H: F043BH GAFLPH13L: F0446H, GAFLPH13H: F0447H
GAFLPH14L: F0452H, GAFLPH14H: F0453H GAFLPH15L: F045EH, GAFLPH15H: F045FH
b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0
GAFLDLC[3:0] GAFLPTR[11:0]
After Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Bit Symbol Bit Name Description R/W
15 to 12 GAFLDLC
[3:0]
Receive Rule DLC
b15 b14 b13 b12
0 0 0 0 : DLC check is disabled.
0 0 0 1 : 1 data byte
0 0 1 0 : 2 data bytes
0 0 1 1 : 3 data bytes
0 1 0 0 : 4 data bytes
0 1 0 1 : 5 data bytes
0 1 1 0 : 6 data bytes
0 1 1 1 : 7 data bytes
1 X X X : 8 data bytes
R/W
11 to 0 GAFLPTR
[11:0]
Receive Rule Label Set the 12-bit label information. R/W
Modify the GAFLPHj register only when the RPAGE bit in the GRWCR register is set to 0 in global reset mode.
GAFLDLC[3:0] Bits
These bits are used to set the minimum data length necessary for receiving messages. If the data length of a
message that is being filtered is equal to or larger than the value set by the GAFLDLC[3:0] bits, the message
passes the DLC check. Setting these bits to B'0000 disables the DLC check function allowing messages with
any data length to pass the DLC check.
GAFLPTR [11:0] Bits
These bits are used to set a 12-bit label to be attached to messages that have passed through the filter. A label
is attached when a message is stored in the receive buffer or the FIFO buffer.

Table of Contents

Other manuals for Renesas RL78 Series

Related product manuals