Rohde & Schwarz MXO 4 Series - Page 816

Remote control commandsMXO 4 Series
816User Manual 1335.5337.02 ─ 07
17.16.7.2 Filter
There are two commands for each parameter, that you can use for defining the LIN
settings.
For example, to set the Frame type =Data > Field =Id >Id value you can use one of the
following commands:
●
SBUS:SPMI:FILTer:FRAMe1:FLD1:DMIN 00
Defines the parameter by using the index <m> for the frame number and <n> for
the field number.
●
SBUS:SPMI:FILTer:DMIN "Data", "Address", 00
Defines the parameter by using the frame and field name.
SBUS<sb>:SPMI:FILTer:CHKall.......................................................................................816
SBUS<sb>:SPMI:FILTer:CLR.......................................................................................... 817
SBUS<sb>:SPMI:FILTer:INVert........................................................................................817
SBUS<sb>:SPMI:FILTer:RST.......................................................................................... 817
SBUS<sb>:SPMI:FILTer:CHKall.......................................................................................817
SBUS<sb>:SPMI:FILTer:CLR.......................................................................................... 817
SBUS<sb>:SPMI:FILTer:INVert........................................................................................818
SBUS<sb>:SPMI:FILTer:RST.......................................................................................... 818
SBUS<sb>:SPMI:FILTer:BIT............................................................................................818
SBUS<sb>:SPMI:FILTer:FRAMe<fr>:FLD<fl>:BIT..............................................................818
SBUS<sb>:SPMI:FILTer:DMAX....................................................................................... 819
SBUS<sb>:SPMI:FILTer:FRAMe<fr>:FLD<fl>:DMAX......................................................... 819
SBUS<sb>:SPMI:FILTer:DMIN........................................................................................ 819
SBUS<sb>:SPMI:FILTer:FRAMe<fr>:FLD<fl>:DMIN.......................................................... 819
SBUS<sb>:SPMI:FILTer:DOPerator................................................................................. 819
SBUS<sb>:SPMI:FILTer:FRAMe<fr>:FLD<fl>:DOPerator................................................... 819
SBUS<sb>:SPMI:FILTer:ERENable..................................................................................820
SBUS<sb>:SPMI:FILTer:ERRor<n>:ENABle..................................................................... 820
SBUS<sb>:SPMI:FILTer:IOPerator...................................................................................820
SBUS<sb>:SPMI:FILTer:FRAMe<fr>:FLD<fl>:IOPerator.....................................................820
SBUS<sb>:SPMI:FILTer:IMIN..........................................................................................820
SBUS<sb>:SPMI:FILTer:FRAMe<fr>:FLD<fl>:IMIN............................................................820
SBUS<sb>:SPMI:FILTer:IMAX.........................................................................................821
SBUS<sb>:SPMI:FILTer:FRAMe<fr>:FLD<fl>:IMAX...........................................................821
SBUS<sb>:SPMI:FILTer:FRENable..................................................................................821
SBUS<sb>:SPMI:FILTer:FRAMe<fr>:ENABle....................................................................821
SBUS<sb>:SPMI:FILTer:FIENable................................................................................... 821
SBUS<sb>:SPMI:FILTer:FRAMe<fr>:FLD<fl>:ENABle....................................................... 821
SBUS<sb>:SPMI:FILTer:CHKall
Enables the filter for all available frames and error types.
Suffix:
<sb>
.
1...4, index of the serial bus
Usage: Setting only
Asynchronous command
Protocols