Mindray BeneVision N22 - Page 15

BeneVision N22/N19 Patient Monitor Operator’s Manual 9
22 Monitoring Carbon Dioxide (CO
2
) ................................................................................................................................22 - 1
22.1 CO
2
Introduction ........................................................................................................................................................................................22 - 2
22.2 CO
2
Safety Information ............................................................................................................................................................................22 - 3
22.3 CO
2
Measurement Limitations ..............................................................................................................................................................22 - 3
22.4 CO
2
Display ..................................................................................................................................................................................................22 - 3
22.5 Measuring CO
2
Using Sidestream/Microstream CO
2
Module ...................................................................................................22 - 4
22.5.1 Preparing to Measure CO
2
Using Sidestream CO
2
Module ..........................................................................................22 - 4
22.5.2 Preparing to Measure CO
2
Using Microstream CO
2
Module .......................................................................................22 - 6
22.5.3 Zeroing the Sidestream/Microstream CO
2
Module ........................................................................................................22 - 6
22.6 Measuring CO
2
Using Mainstream CO
2
Module ............................................................................................................................. 22 - 7
22.6.1 Preparing to Measure CO
2
Using Mainstream CO
2
Module .........................................................................................22 - 7
22.6.2 Zeroing the Mainstream CO
2
sensor ....................................................................................................................................22 - 8
22.7 Changing Settings for All CO
2
Modules .............................................................................................................................................22 - 8
22.7.1 Changing CO
2
Alarm Settings .................................................................................................................................................22 - 8
22.7.2 Changing the CO
2
Unit ..............................................................................................................................................................22 - 8
22.7.3 Setting the CO
2
Waveform .......................................................................................................................................................22 - 9
22.7.4 Setting the RR Source .................................................................................................................................................................22 - 9
22.7.5 Entering the Standby Mode .....................................................................................................................................................22 - 9
22.7.6 Entering the Intubation Mode ................................................................................................................................................22 - 9
22.8 Changing Settings for Sidestream and Microstream CO
2
Module) .........................................................................................22 - 9
22.8.1 Setting the Auto Standby .........................................................................................................................................................22 - 9
22.8.2 Setting Humidity Compensation .........................................................................................................................................22 - 10
22.9 Changing O
2
Settings (For Sidestream CO
2
Module Only) .......................................................................................................22 - 10
22.9.1 Changing O
2
Alarm Settings ..................................................................................................................................................22 - 10
22.9.2 Changing the O
2
Unit ...............................................................................................................................................................22 - 10
22.9.3 Setting the O2 Waveform .......................................................................................................................................................22 - 10
22.10 Setting the Gas Compensation ........................................................................................................................................................22 - 11
22.11 Choosing a Time Interval for Peak-Picking ...................................................................................................................................22 - 11
22.12 Changing Barometric Pressure .........................................................................................................................................................22 - 12
22.13 Performing the Leakage Test ............................................................................................................................................................22 - 12
22.14 Replacing the Galvanic Oxygen Sensor .........................................................................................................................................22 - 12
22.15 Calibrating the Galvanic Oxygen Sensor ......................................................................................................................................22 - 13
22.16 CO
2
Calibration .......................................................................................................................................................................................22 - 13
22.17 CO
2
Troubleshooting ...........................................................................................................................................................................22 - 13
22.17.1 Troubleshooting the Sidestream/Microstream CO
2
Module ..................................................................................22 - 13
22.17.2 Troubleshooting the Mainstream CO
2
Module ............................................................................................................22 - 14
22.18 Oridion Information ..............................................................................................................................................................................22 - 14
23 Monitoring Anesthetic ..................................................................................................................................................23 - 1
23.1 AG Introduction ..........................................................................................................................................................................................23 - 2
23.2 AG Measurement Limitations ................................................................................................................................................................23 - 3
23.3 AG Display ....................................................................................................................................................................................................23 - 3
23.4 AG Equipment to Patient Connection ................................................................................................................................................23 - 4
23.5 Preparing for AG Monitoring .................................................................................................................................................................23 - 4
23.6 MAC Values ..................................................................................................................................................................................................23 - 5
23.7 Changing AG Settings ..............................................................................................................................................................................23 - 6
23.7.1 Changing AG Alarm Settings ...................................................................................................................................................23 - 6
23.7.2 Setting the O
2
Compensation ................................................................................................................................................. 23 - 6
23.7.3 Entering the Standby Mode .....................................................................................................................................................23 - 6
23.7.4 Setting Auto Standby .................................................................................................................................................................23 - 7
23.7.5 Setting the AG Waveform ......................................................................................................................................................... 23 - 7
23.7.6 Setting the RR Source ................................................................................................................................................................. 23 - 7
23.7.7 Entering the Intubation Mode ................................................................................................................................................23 - 7
23.7.8 Changing the Gas Unit ...............................................................................................................................................................23 - 7
23.8 Changing the Anesthetic Agent ...........................................................................................................................................................23 - 8
23.9 AG Troubleshooting ..................................................................................................................................................................................23 - 8