Rohde & Schwarz MXO 4 Series - Page 830

Remote control commandsMXO 4 Series
830User Manual 1335.5337.02 ─ 07
Usage: Setting only
Asynchronous command
17.16.8.2 Filter
There are two commands for each parameter, that you can use for defining the
10BASE-T1S settings.
For example, to set the Frame type =Data > Field =Id >Id value you can use one of the
following commands:
●
SBUS:TNOS:FILTer:FRAMe1:FLD1:DMIN 00
Defines the parameter by using the index <m> for the frame number and <n> for
the field number.
●
SBUS:TNOS:FILTer:DMIN "Data", "Address", 00
Defines the parameter by using the frame and field name.
SBUS<sb>:TNOS:FILTer:CHKall......................................................................................830
SBUS<sb>:TNOS:FILTer:CLR......................................................................................... 831
SBUS<sb>:TNOS:FILTer:RST......................................................................................... 831
SBUS<sb>:TNOS:FILTer:INVert.......................................................................................831
SBUS<sb>:TNOS:FILTer:BIT...........................................................................................831
SBUS<sb>:TNOS:FILTer:FRAMe<fr>:FLD<fl>:BIT............................................................ 831
SBUS<sb>:TNOS:FILTer:DMAX...................................................................................... 832
SBUS<sb>:TNOS:FILTer:FRAMe<fr>:FLD<fl>:DMAX........................................................ 832
SBUS<sb>:TNOS:FILTer:DMIN....................................................................................... 832
SBUS<sb>:TNOS:FILTer:FRAMe<fr>:FLD<fl>:DMIN......................................................... 832
SBUS<sb>:TNOS:FILTer:DOPerator................................................................................ 832
SBUS<sb>:TNOS:FILTer:FRAMe<fr>:FLD<fl>:DOPerator.................................................. 832
SBUS<sb>:TNOS:FILTer:ERENable................................................................................ 833
SBUS<sb>:TNOS:FILTer:ERRor<n>:ENABle.................................................................... 833
SBUS<sb>:TNOS:FILTer:FIENable.................................................................................. 833
SBUS<sb>:TNOS:FILTer:FRAMe<fr>:FLD<fl>:ENABle...................................................... 833
SBUS<sb>:TNOS:FILTer:IMAX........................................................................................833
SBUS<sb>:TNOS:FILTer:FRAMe<fr>:FLD<fl>:IMAX..........................................................833
SBUS<sb>:TNOS:FILTer:IMIN.........................................................................................834
SBUS<sb>:TNOS:FILTer:FRAMe<fr>:FLD<fl>:IMIN...........................................................834
SBUS<sb>:TNOS:FILTer:IOPerator..................................................................................834
SBUS<sb>:TNOS:FILTer:FRAMe<fr>:FLD<fl>:IOPerator................................................... 834
SBUS<sb>:TNOS:FILTer:FRENable.................................................................................835
SBUS<sb>:TNOS:FILTer:FRAMe<fr>:ENABle...................................................................835
SBUS<sb>:TNOS:FILTer:CHKall
Enables the filter for all available frames and error types.
Suffix:
<sb>
.
1...4, index of the serial bus
Usage: Setting only
Asynchronous command
Protocols