SYSMEX SF-3000 User Manual

RESULT INTERPRETATION/REPORTS, Stored Data, List Display
Sysmex SF-3000 Operator's Manual -- Revised September 1995 4-15
3.4 WBC+5Diff% Screen (Page 4)
This screen lists the WBC count and the percent values for the following 5DIFF
parameters: NEUT%, LYMPH%, MONO%, EO% and BASO%.
To switch to this screen from "P3. WBC+5Diff#", press [→] key. To switch to this
screen from "P5. RBC/PLT", press [←] key.
SAMPLE NO. WBC NEUT% LYMPH% MONO% EO% BASO%
900/1000(1000)
Sysmex
DP:1234567890123 XM HC GP DP SU
Ready Manual Mode Next No.1234567890123
Sampler
123-56789-101*
123-56789-101*
123-56789-102
123-56789-103
ERR0000000001
ERR0000000002
123-56789-106
123-56789-107
123-56789-108
ERR0000000003
123-56789-110
123-56789-111
123-56789-112
123-56789-113
123-56789-114
123-56789-115
ERR0000000004
ERR0000000005
ERR0000000006
ERR0000000007
1.64
7.67
4.82
5.90
1.67
1.77
1.06
11.79
5.20
1.70
6.21
6.73
8.44
4.37
23.31
6.38
1.90
1.84
1.86
1.82
47.8
83.6
67.4
64.9
40.4
51.4
46.6
81.6
59.1
68.3
54.2
37.0
81.3
53.7
93.8
56.4
70.7
60.2
63.2
56.8
36.0
7.7
21.1
22.5
42.2
38.7
38.6
15.0
19.5
16.6
25.9
45.8
11.3
37.8
2.9
30.5
12.8
25.0
23.5
26.1
7.8
5.1
7.7
11.4
11.5
4.6
10.2
2.8
7.3
11.5
10.6
8.4
6.0
6.4
3.1
0.0
12.7
10.3
10.3
11.0
6.9
2.8
2.7
0.2
2.6
4.4
3.3
0.4
12.2
2.8
8.0
7.8
0.6
1.5
0.0
11.2
1.5
3.4
0.9
5.0
2.0
0.8
1.0
1.0
3.3
0.9
1.3
0.2
1.9
0.8
1.3
1.0
0.8
0.6
0.2
1.9
2.3
1.1
2.1
1.1
=ALL SAMPLES = Stored Data
Search
Select
Display
Output
SortGraphic Valid.
More Return
Next
Prev
Mark
→
←
↑
↓
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
Figure 4-5: WBC+5Diff% Screen (P4)
1) "v" (validated) Mark
Indicates that this data is validated. Refer to Section 5: Data Validation in this
chapter.
2) SAMPLE NO.
Sample No., as read by bar code reader or input by the operator.
3) Indications
The following indications appear to the right of analysis data:
① ! (backlit in red):
Indicates that the data is outside the Critical Limits.
➁ * (backlit in red):
Indicates that the data is outside the Linearity Limits.
➂ +, – (backlit in red):
Indicates that the data is outside the Sampler Stop Limits.
➃ * (backlit in yellow):
Indicates that the data is unreliable because of an abnormality detected in the
sample.
⑤ +, – (backlit in yellow):
Indicates that the data is outside the Mark Limits.
NOTE: The above indications are listed on the priority basis.

SYSMEX SF-3000 Specifications

General

Brand	SYSMEX
Model	SF-3000
Category	Measuring Instruments
Language	English