RESULT INTERPRETATION/REPORTS
Sysmex SF-3000 Operator's Manual -- Revised September 1995 4-25
6. MARK DATA
By pressing the [Mark] keypad in the List Display, the Mark Data screen as shown in
Figure 4-11 will be displayed. In this program data is marked with a yellow square on
the left edge of the screen for output and/or delete.
NOTE: • Refer to Section 11.2 : Marked Data (Output) or Section 12.2: Marked
Data (Delete).
• The marks will be deleted automatically when the power turns OFF.
Stored Data
DATE TIME SEQ. SAMPLE NO. RACK TUBE OUT POS ERROR MARK STOP
Sampler
Sysmex
12/04
12/04
12/04
12/04
12/04
12/04
12/04
12/04
12/04
12/04
12/04
12/04
12/04
12/04
12/04
12/04
12/04
12/04
12/04
12/04
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
v
DP:1234567890123
10:58
11:00
11:00
11:01
11:01
11:02
11:02
11:03
11:03
11:04
11:04
11:05
11:05
11:06
11:06
11:07
11:07
11:08
11:08
11:09
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
123-56789-101*I
123-56789-101*I
123-56789-102 I
123-56789-103 I
ERR0000000001
ERR0000000002
123-56789-106 I
123-56789-107 I
123-56789-108 I
123-56789-109 I
123-56789-110 I
123-56789-111 I
123-56789-112 I
123-56789-113 I
123-56789-114 I
123-56789-115 I
ERR0000000003
ERR0000000004
ERR0000000005
ERR0000000006
1011
1011
1011
1011
1011
1011
1011
1011
1011
1011
1012
1012
1012
1012
1012
1012
1012
1012
1012
1012
DGH
DGH
DGH
DGH
DGH
DGH
DGH
DGH
DGH
DGH
DGH
DGH
DGH
DGH
DGH
DGH
DGH
DGH
DGH
DGH
DMC
D
DMC
DMC
M
DMC
D
C
DMC
DMC
DMC
DMC
Func.
Func.
Func.
Result
Func.
Func.
Func.
Func.
A 10
A 1
A 2
A 3
A 4
A 5
A 6
A 7
A 8
A 9
A 10
A 1
A 2
A 3
A 4
A 5
A 6
A 7
A 8
A 9
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
XM HC GP DP SU
Ready
Manual Mode Next No.1234567890123
All
Clear
CancelBy Date Current
Next
Prev
Mark
→
←
↑
↓
= ALL SAMPLES =
0/ 100 (100)
Figure 4-11: Mark Data Screen
Key Operation:
[All Clear] : Deletes existing yellow marks.
[By Date] : Marks with a yellow mark all data having the same date as the data
the cursor is on. If same-date data were already marked with
yellow marks, the marks are deleted.
[Current] : Marks the data the cursor is on with a yellow mark. If the data was
already marked with a yellow mark, the mark is deleted.
[Cancel] : Returns to the List Display.
NOTE: If there is any marked data that has not been output or deleted, the
message window "## marked data has been exist!!!" appears when
the [Mark] key is pressed.
Delete the unprocessed mark(s), or delete or output the marked data.
To Next Page
Loading...
Need help?
General
