Rohde & Schwarz MXO 4 Series - Page 733

Remote control commandsMXO 4 Series
733User Manual 1335.5337.02 ─ 07
17.16.3.3 Filter
There are two commands for each parameter, that you can use for defining the I2C
settings.
For example, to set the Frame type =WRITe > Field =Address >Data value you can
use one of the following commands:
●
SBUS:I2C:FILTer:FRAMe1:FLD1:DMIN 01100
Defines the parameter by using the index <m> for the frame number and <n> for
the field number.
●
SBUS:I2C:FILTer:DMIN "WRITe", "Address", 01100
Defines the parameter by using the frame and field name.
SBUS<sb>:I2C:FILTer:CHKall......................................................................................... 733
SBUS<sb>:I2C:FILTer:CLR............................................................................................. 734
SBUS<sb>:I2C:FILTer:INVert...........................................................................................734
SBUS<sb>:I2C:FILTer:RST............................................................................................. 734
SBUS<sb>:I2C:FILTer:ENABle........................................................................................ 734
SBUS<sb>:I2C:FILTer:FRENable.....................................................................................735
SBUS<sb>:I2C:FILTer:FRAMe<fr>:ENABle.......................................................................735
SBUS<sb>:I2C:FILTer:DMAX.......................................................................................... 735
SBUS<sb>:I2C:FILTer:FRAMe<fr>:FLD<fl>:DMAX............................................................ 735
SBUS<sb>:I2C:FILTer:DMIN........................................................................................... 735
SBUS<sb>:I2C:FILTer:FRAMe<fr>:FLD<fl>:DMIN............................................................. 735
SBUS<sb>:I2C:FILTer:DOPerator.................................................................................... 736
SBUS<sb>:I2C:FILTer:FRAMe<fr>:FLD<fl>:DOPerator...................................................... 736
SBUS<sb>:I2C:FILTer:ERENable.................................................................................... 736
SBUS<sb>:I2C:FILTer:ERRor<n>:ENABle........................................................................ 736
SBUS<sb>:I2C:FILTer:IMAX............................................................................................736
SBUS<sb>:I2C:FILTer:FRAMe<fr>:FLD<fl>:IMAX..............................................................736
SBUS<sb>:I2C:FILTer:IMIN.............................................................................................737
SBUS<sb>:I2C:FILTer:FRAMe<fr>:FLD<fl>:IMIN...............................................................737
SBUS<sb>:I2C:FILTer:IOPerator......................................................................................737
SBUS<sb>:I2C:FILTer:FRAMe<fr>:FLD<fl>:IOPerator....................................................... 737
SBUS<sb>:I2C:FILTer:BIT...............................................................................................737
SBUS<sb>:I2C:FILTer:FRAMe<fr>:FLD<fl>:BIT................................................................ 737
SBUS<sb>:I2C:FILTer:FIENable...................................................................................... 738
SBUS<sb>:I2C:FILTer:FRAMe<fr>:FLD<fl>:ENABle.......................................................... 738
SBUS<sb>:I2C:FILTer:CHKall
Enables the filter for all available frames and error types.
Suffix:
<sb>
.
1...4, index of the serial bus
Usage: Setting only
Asynchronous command
Manual operation: See "Check all, Clear, Invert, Reset" on page 342
Protocols