Schweitzer Engineering Laboratories SEL-421-4 - Page 769

Date Code 20171006 Instruction Manual SEL-400 Series Relays
SEL-400 Series RelaysInstruction Manual
List of Figures
Figure 2.1 QuickSet Communication Parameters Dialog Box .....................................................................2.3
Figure 2.2 QuickSet Database Manager Relay Database..............................................................................2.5
Figure 2.3 QuickSet Database Manager Copy/Move ...................................................................................2.6
Figure 2.4 QuickSet Software Driver Information in the FID String..................................................................2.7
Figure 2.5 Relay Settings Driver Version Number............................................................................................2.8
Figure 2.6 Retrieving the Device Part Number...........................................................................................2.10
Figure 2.7 Setting the Relay Part Number in QuickSet ..............................................................................2.10
Figure 2.8 SECINC Setting.........................................................................................................................2.11
Figure 2.9 SEL-487E Nominal Current Selection ......................................................................................2.11
Figure 2.10 SECINC Disabled......................................................................................................................2.12
Figure 2.11 Station DC Settings ...................................................................................................................2.13
Figure 2.12 Enable EDCMON in Global Settings........................................................................................2.13
Figure 2.13 DC Monitor Settings Enabled....................................................................................................2.14
Figure 2.14 QuickSet Settings Editor ...........................................................................................................2.15
Figure 2.15 Ellipsis Button ...........................................................................................................................2.16
Figure 2.16 Location of Ellipsis Button........................................................................................................2.17
Figure 2.17 QuickSet Expression Builder.....................................................................................................2.18
Figure 2.18 Virtual Relay Front Panel ..........................................................................................................2.19
Figure 2.19 Control Window ........................................................................................................................2.21
Figure 2.20 Retrieving an Event History ......................................................................................................2.23
Figure 2.21 Event Waveform Window .........................................................................................................2.23
Figure 2.22 Sample Event Oscillogram ........................................................................................................2.24
Figure 2.23 Retrieving Event Report Waveforms ........................................................................................2.24
Figure 2.24 Sample Phasors Event Waveform Screen..................................................................................2.24
Figure 2.25 Sample Harmonic Analysis Event Waveform Screen...............................................................2.25
Figure 2.26 Sample Event Report Summary Screen.....................................................................................2.25
Figure 2.27 Sample Event Waveform Settings Screen .................................................................................2.26
Figure 2.28 Combine Time-Synchronized Events Submenu Screen............................................................2.27
Figure 2.29 Selection of the First Event Report............................................................................................2.28
Figure 2.30 First Event of the Analysis ........................................................................................................2.28
Figure 2.31 Screen After Reading All Three Events ....................................................................................2.29
Figure 2.32 Screen for Selecting Analog Channels and Digital Relay Word Bits .......................................2.29
Figure 2.33 Selection of Analog Channels and Digital Relay Word Bits.....................................................2.30
Figure 2.34 Data From Three Separate Event Reports Combined in a Single Report..........................................2.31
Figure 2.35 Traces of the Three Analog Channels .......................................................................................2.31
Figure 3.1 Sample Relay Serial Number Label ............................................................................................3.2
Figure 3.2 PORT F, LCD Display, and Navigation Pushbuttons .................................................................3.3
Figure 3.3 Report Header..............................................................................................................................3.5
Figure 3.4 HTTP Server Login Screen .........................................................................................................3.6
Figure 3.5 Example HTTP Server Meter Page .............................................................................................3.7
Figure 3.6 Access Level Structure ................................................................................................................3.8
Figure 3.7 Relay Status ...............................................................................................................................3.12
Figure 3.8 QuickSet Communication Parameters and Password Entry......................................................3.13
Figure 3.9 Retrieving Relay Status in QuickSet .........................................................................................3.14
Figure 3.10 Checking Relay Status From the Front-Panel LCD ..................................................................3.14
Figure 3.11 Example Relay Settings Structure Overview ............................................................................3.16
Figure 3.12 Default Alias Settings................................................................................................................3.18
Figure 3.13 Using Text-Edit Mode Line Editing to Set Aliases...................................................................3.19
Figure 3.14 Using Text-Edit Mode Line Editing to Set Protection Logic....................................................3.19
Figure 3.15 Components of SET Commands ...............................................................................................3.20
Figure 3.16 Example Global Settings ...........................................................................................................3.21