SYSMEX SF-3000 - Page 595

Sysmex SF-3000 Operator's Manual -- Revised July 1996 i
INDEX
0.5 kg/cm
2
Error, Troubleshooting 8-9
0.5 kg/cm
2
Regulator 9-5, 10-24
0.6 kg/cm
2
Error, Troubleshooting 8-9
0.6 kg/cm
2
Regulator 9-5, 10-24
2.0 kg/cm
2
Error, Troubleshooting 8-10
2.0 kg/cm
2
Pressure, Adjust 9-4
2.0 kg/cm
2
Regulator 9-3, 10-32
4DIFF Analysis, Principle 10-8
250 mmHg Bellows Unit 9-5
250 mmHg Error, Troubleshooting 8-10
[A]
Abnormal IP Messages 4-3
Set Limits 11-24
Abnormal Limits, Set 11-24
Acceptable Background Limits 2-5
Acceptable Barcodes 1-24
Accuracy 1-22
Check at Installation B-33
Differential 1-23
Ack Code Error, Troubleshooting 8-49
Ack Time Out Error, Troubleshooting 8-49
Action Message, Error Log 8-94
Adapter, Sample Rack 2-30
Adjust
0.5 kg/cm
2
9-7
0.6 kg/cm
2
9-6
2.0 kg/cm
2
9-4
250 mmHg Vacuum 9-8
ID Bar Code Reader 9-10, B-34
LCD Contrast 9-9
Vacuum, Main Unit 9-8
Vacuum, Pneumatic Unit 9-5
Air Drier 10-20
Installation B-22
Air Filter 10-24
Alarms 1-18
All Data, Stored Data
Delete 4-61
Output 4-52
All Data, Work List, Delete 3-10
All Samples, Select Display 4-34
Alphabetical Error Message Index 8-2
Analysis Error Window 4-20
<Analysis Error>, Troubleshooting 8-38
Analysis Mode Display 1-11
Analysis Parameters 1-9
Analysis Process, Status Display 8-92
Analysis Status 1-10
Analyze, Calibration 7-8
Analyzer Condition, Status Display 8-91
Anti-Shock Rubber No. 49, Replace 5-64
Aperture Diameter 1-21
Applicable Bar Codes C-17
Applicable Characters, Bar Code C-28
As Needed Maintenance 5-29
Auto Erase, Set 11-9
Auto Limit, QC, Setting 6-23
Auto Management, Setting Programs 11-3
Auto Mode Stop Condition, Set 11-22
Auto Mode
Procedures 2-29
QC Analysis (L-J) 2-12, 6-44
Sample Volume 2-29
Auto Output 4-62
Condition, Set 11-6
Data Specification, Set 11-8
Auto Output Condition, Set 11-6
Auto Output Mode, Set 11-8
Auto Setting, QC, Target/Limit 6-21
Auto Target, QC, Setting 6-22
Auto Validation, Set 11-11
Available Reporting Units 11-46
[B]
Background Error, Troubleshooting 8-39
Background Limits, Acceptable 2-5
Backup
Setting Values 11-57
Stored Data 4-54
Work List 3-14
Bar Code Label
Specification C-17
Rack ID 2-30, C-17
Sample ID C-17
Bar Code Reader
Adjustment 9-10, B-34
Install B-12
Setting 11-52
Test 8-74
Barcodes, Acceptable 1-24
Battery Backup, Procedures B-28
Baud Rate
Serial Interface C-2
Set 11-35
BBM Unstorageable, Troubleshooting 8-45
Bellows Unit 9-5, 10-24