Keysight Technologies M8000 Series

144 Keysight M8000 Series of BER Test Solutions User Guide
4 User Interface - M8020A Display Views
BUJ Amplitude Depends on PJ1 amplitude, PJ2
amplitude, RJ amplitude, sRJ amp1
and sRJ amp2
":SOURce:JITTer:HFRequency:PERiodic1:AMPLitude
:SOURce:JITTer:HFRequency:PERiodic2:AMPLitude
:SOURce:JITTer:HFRequency:RANDom:AMPLitude
:SOURce:JITTer:HFRequency:SPECtrally:AMPLitude1
:SOURce:JITTer:HFRequency:SPECtrally:AMPLitude2
"
RJ State "Value doesn't applicable if state is
Off
Also depends on sRJ state"
":SOURce:JITTer:HFRequency:RANDom:STATe
:SOURce:JITTer:HFRequency:SPECtrally:STATe"
RJ Amplitude Depends on PJ1 amplitude, PJ2
amplitude, BUJ amplitude, sRJ
amp1 and sRJ amp2
":SOURce:JITTer:HFRequency:PERiodic1:AMPLitude
:SOURce:JITTer:HFRequency:PERiodic2:AMPLitude
:SOURce:JITTer:HFRequency:BUNCorrelate:AMPLitu
de
:SOURce:JITTer:HFRequency:SPECtrally:AMPLitude1
:SOURce:JITTer:HFRequency:SPECtrally:AMPLitude2
"
sRJ State "Value doesn't applicable if state is
Off
Also depends on RJ and BUJ state"
":SOURce:JITTer:HFRequency:SPECtrally:STATe
:SOURce:JITTer:HFRequency:RANDom:STATe
:SOURce:JITTer:HFRequency:BUNCorrelate:STATe"
sRJ Amplitude
1(RMS) LF
Depends on PJ1 amplitude, PJ2
amplitude, BUJ amplitude, RJ amp
and sRJ amp2
":SOURce:JITTer:HFRequency:PERiodic1:AMPLitude
:SOURce:JITTer:HFRequency:PERiodic2:AMPLitude
:SOURce:JITTer:HFRequency:BUNCorrelate:AMPLitu
de
:SOURce:JITTer:HFRequency:RANDom:AMPLitude
:SOURce:JITTer:HFRequency:SPECtrally:AMPLitude2
"
sRJ Amplitude
2(RMS) HF
Depends on PJ1 amplitude, PJ2
amplitude, BUJ amplitude, RJ amp
and sRJ amp1
":SOURce:JITTer:HFRequency:PERiodic1:AMPLitude
:SOURce:JITTer:HFRequency:PERiodic2:AMPLitude
:SOURce:JITTer:HFRequency:BUNCorrelate:AMPLitu
de
:SOURce:JITTer:HFRequency:RANDom:AMPLitude
:SOURce:JITTer:HFRequency:SPECtrally:AMPLitude1
"
sRJ State M1.DataOut1 BUJ State (Data
Out )
If sRJ is ON, then BUJ state cannot
be enabled
":SOURce:JITTer:HFRequency:SPECtrally:STATe
:SOURce:JITTer:HFRequency:BUNCorrelate:STATe"
RJ State (Data
Out )
If sRJ is ON, then RJ state cannot be
enabled
":SOURce:JITTer:HFRequency:SPECtrally:STATe
:SOURce:JITTer:HFRequency:RANDom:STATe"
BUJ State (Clock
Out )
If sRJ is ON, then BUJ state cannot
be enabled
":SOURce:JITTer:HFRequency:SPECtrally:STATe
:SOURce:JITTer:HFRequency:BUNCorrelate:STATe"
Functional
block /
Parameter
Identifier
Location
Dependent
Parameters
Description Related /Dependent SCPI