Keysight Technologies M8000 Series User Manual

Keysight M8000 Series of BER Test Solutions User Guide 145
User Interface - M8020A Display Views 4
RJ State (Clock
Out )
If sRJ is ON, then RJ state cannot be
enabled
":SOURce:JITTer:HFRequency:SPECtrally:STATe
:SOURce:JITTer:HFRequency:RANDom:STATe"
BUJ State M1.DataOut1 sRJ State (Data
Out )
If BUJ state is ON, then DataOut sRJ
cannot be enabled
":SOURce:JITTer:HFRequency:SPECtrally:STATe
:SOURce:JITTer:HFRequency:BUNCorrelate:STATe"
sRJ State (Clock
Out )
If BUJ state is ON, then ClockOut
sRJ cannot be enabled
":SOURce:JITTer:HFRequency:SPECtrally:STATe
:SOURce:JITTer:HFRequency:BUNCorrelate:STATe"
RJ State M1.DataOut1 sRJ State (Data
Out )
If RJ state is ON, then DataOut sRJ
cannot be enabled
":SOURce:JITTer:HFRequency:RANDom:STATe
:SOURce:JITTer:HFRequency:SPECtrally:STATe"
sRJ State (Data
Out )
If RJ state is ON, then ClockOut sRJ
cannot be enabled
":SOURce:JITTer:HFRequency:RANDom:STATe
:SOURce:JITTer:HFRequency:SPECtrally:STATe"
sRJ State M1.DataOut1 RJ State (Data
Out )
If sRJ state is ON, then DataOut RJ
cannot be enabled
":SOURce:JITTer:HFRequency:SPECtrally:STATe
:SOURce:JITTer:HFRequency:RANDom:STATe"
BUJ State (Data
Out )
If sRJ state is ON, then DataOut BUJ
cannot be enabled
":SOURce:JITTer:HFRequency:SPECtrally:STATe
:SOURce:JITTer:HFRequency:BUNCorrelate:STATe"
RJ State (Clock
Out )
If sRJ state is ON, then ClockOut RJ
cannot be enabled
":SOURce:JITTer:HFRequency:SPECtrally:STATe
:SOURce:JITTer:HFRequency:RANDom:STATe"
BUJ State (Clock
Out )
If sRJ state is ON, then ClockOut
BUJ cannot be enabled
":SOURce:JITTer:HFRequency:SPECtrally:STATe
:SOURce:JITTer:HFRequency:BUNCorrelate:STATe"
RJ Low
Pass Filter
as 1000
MHz
M1.DataOut1 Depends on Data
Rate (Synthesizer
frequency)
Can only be selected is Data Rate is
above 7.5 GHz
":SOURce:JITTer:HFRequency:RANDom:STATe
:SOURce:FREQuency
:SOURce:JITTer:HFRequency:RANDom:FILTer:LPASs"
Jitter
Sweep
State
M1.DataOut1 RJ State (Data
Out )
If Jitter Sweep state is ON, then
DataOut RJ cannot be enabled
":SOURce:JITTer:SWEep:STATe
:SOURce:JITTer:HFRequency:RANDom:STATe"
PJ2 State (Data
Out )
If Jitter Sweep state is ON, then
DataOut PJ2 cannot be enabled
":SOURce:JITTer:SWEep:STATe
:SOURce:JITTer:HFRequency:PERiodic2:STATe"
PJ2 State (Clock
Out )
If Jitter Sweep state is ON, then
ClockOut PJ2 cannot be enabled
":SOURce:JITTer:SWEep:STATe
:SOURce:JITTer:HFRequency:PERiodic2:STATe"
Jitter
Sweep
Amplitude,
start and
stop
frequency
M1.DataOut1 Jitter sweep
mode
User programmable only If Mode is
selected as Constant amplitude
":SOURce:JITTer:SWEep:STATe
:SOURce:JITTer:SWEep:AMPLitude:MODE
:SOURce:JITTer:SWEep:AMPLitude:VALue
:SOURce:JITTer:SWEep:FREQuency:STARt
:SOURce:JITTer:SWEep:FREQuency:STOP"
Functional
block /
Parameter
Identifier
Location
Dependent
Parameters
Description Related /Dependent SCPI

Keysight Technologies M8000 Series Specifications

General

Brand	Keysight Technologies
Model	M8000 Series
Category	Test Equipment
Language	English