SYSMEX SF-3000 - Page 602

viii Sysmex SF-3000 Operator's Manual -- Revised September 1995
Remove Packing Material B-7
Main Unit, Chassis B-9
Main Unit, Front Cover B-7
Main Unit, Front Panel B-7
Main Unit, Rear Panel B-10
Pneumatic Unit B-11
SRV B-10
Replace
Anti-Shock Rubber No. 49 5-64
Belt No. 6 5-67
Fuses 5-65
Hand Clipper 5-62
Piercer, MCP Unit 5-58
Piercer, Sampler 5-51
Reagent 5-46
Rubber Plate No. 39, Sampler 5-63
Waste Container 5-45
Replace Piercer, Guide 8-58
Replace Reagent Container
FBA, Troubleshooting 8-15
FDO, Troubleshooting 8-15
FDT, Troubleshooting 8-15
PK (1), Troubleshooting 8-15
PK (2), Troubleshooting 8-15
PK (3), Troubleshooting 8-15
SLS, Troubleshooting 8-15
Replace Sheath Flow Reagent Sequence 5-43
Replacement Parts Listing 5-74
Replacements 5-46
Requirements on Wide/Narrow Ratio,
Bar Code Label C-18
Reset the Counter 5-69
Restarting the Pneumatic Unit 2-51
Right Interior
Main Unit 10-30
Pneumatic Unit 10-34
Right Side
Main Unit 10-22
Pneumatic Unit 10-33
Rinse Cup 10-25
Rinse Mechanism Motor, Test 8-67
Rinse Motor Controller Error,
Troubleshooting 8-44
Rinse Motor Function Error,
Troubleshooting 8-19
Root Menus 1-14
Menu Tree A-1
RS-232C Signal Level C-3
Rubber Plate No. 39, Replace 5-63
[S]
Safety 1-6
Sample Data Format C-8
Sample Flow Block Diagram 10-4
Sample Information Screen (P1),
Stored Data 4-10
Sample No. Order, Sort, Stored Data 4-45
Sample No., Edit Sample Info. 4-47
Sample No., Search, Stored Data 4-39
Sample Not Asp Error, Troubleshooting 8-22
Sample Rack Adapter 2-30
Sample Volume Required 1-21
Auto Mode 2-29
Capillary Mode 2-23
Closed Mode 2-37
Manual CP Mode 2-43
Manual Mode 2-18
Sampler Com. Error, Troubleshooting 8-44
Sampler CP Mech., Test 8-73
Sampler Operation Errors,
Troubleshooting 8-25
Sampler QC Analysis (L-J) 6-44
Sampler Start Error (Blood Sensor),
Troubleshooting 8-34
Sampler Start Error (Sensor 4),
Troubleshooting 8-34
Sampler Start Error (Sensor 5),
Troubleshooting 8-34
Sampler Stop Condition, Set 11-22
Sampler Stop Limits, Set 11-20
Sampler Unit Sensors 8-25
Sampler Unit
Check 2-3
Install B-13
Sampler Unit, Nomenclature
Top 10-35
Top Interior 10-36
Sampling Data, Display,
Service Data 8-86, 8-88
Scattered Light Measurement System 10-2
Scattergram Generation 10-10
Search, Stored Data 4-38
Bottom 4-38
By Date 4-41
By Sample No. 4-39
Same Day 4-40
Top 4-38
Select Display 4-26
All Samples 4-34
By Date 4-29
By Flagging 4-27
No Output 4-31
QC Data 4-33
Read FD Data 4-35
Select File, QC 6-33
Select Limit# or Limit%, QC 6-6
Select X
or L-J Control 6-6
Select X
/L-J QC Parameters 6-7
Select X
M QC Parameters 6-8