EasyManua.ls Logo

Siemens SINAMICS G120 - Page 538

Siemens SINAMICS G120
924 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
2 Parameters
2.3 Parameters for data sets
SINAMICS G120 Control Units CU240B-2/CU240E-2
538 List Manual (LH11), 01/2016, A5E33839529
r0370[0...n] Motor stator resistance cold / Mot R_stator cold
r0372[0...n] Cable resistance / Mot R_cable
r0373[0...n] Motor rated stator resistance / Mot R_stator rated
r0374[0...n] Motor rotor resistance cold / Mot R_r cold
r0376[0...n] Rated motor rotor resistance / Mot rated R_rotor
r0377[0...n] Motor leakage inductance total / Mot L_leak total
r0378[0...n] Motor stator inductance d axis / Mot L_stator d
r0382[0...n] Motor magnetizing inductance transformed / Mot L_magn transf
r0384[0...n] Motor rotor time constant / damping time constant d axis / Mot T_rotor/T_Dd
r0386[0...n] Motor stator leakage time constant / Mot T_stator leak
r0394[0...n] Rated motor power / Mot P_rated
r0395[0...n] Actual stator resistance / R_stator act
r0396[0...n] Actual rotor resistance / R_rotor act
p0530[0...n] Bearing version selection / Bearing vers sel
p0531[0...n] Bearing code number selection / Bearing codeNo sel
p0532[0...n] Bearing maximum speed / Bearing n_max
p0541[0...n] Load gearbox code number / Load grbx CodeNo
p0542[0...n] Load gearbox maximum speed / Load grbx n_max
p0543[0...n] Load gearbox maximum torque / Load grbx M_max
p0544[0...n] Load gearbox overall ratio (absolute value) numerator / Load grbx ratio N
p0545[0...n] Load gearbox overall ratio (absolute value) denominator / Load grbx ratio D
p0546[0...n] Load gearbox output direction of rotation inversion / Load grbx outp inv
p0550[0...n] Brake type / Brake type
p0551[0...n] Brake code number / Brake code no.
p0552[0...n] Maximum brake speed / Brake n_max
p0553[0...n] Brake holding torque / Brake M_hold
p0554[0...n] Brake moment of inertia / Brake J
p0601[0...n] Motor temperature sensor type / Mot_temp_sens type
p0604[0...n] Mot_temp_mod 2/sensor alarm threshold / Mod 2/sens A_thr
p0605[0...n] Mot_temp_mod 1/2/sensor threshold and temperature value / Mod1/2/sens T_thr
p0606[0...n] Mot_temp_mod 2/sensor timer / Mod 2/sens timer
p0607[0...n] Temperature sensor fault timer / Sensor fault time
p0610[0...n] Motor overtemperature response / Mot temp response
p0611[0...n] I2t motor model thermal time constant / I2t mot_mod T
p0612[0...n] Mot_temp_mod activation / Mot_temp_mod act
p0613[0...n] Mot_temp_mod 1/3 ambient temperature / Mod 1/3 amb_temp
p0614[0...n] Thermal resistance adaptation reduction factor / Therm R_adapt red
p0615[0...n] Mot_temp_mod 1 (I2t) fault threshold / I2t F thresh
p0620[0...n] Thermal adaptation, stator and rotor resistance / Mot therm_adapt R
p0621[0...n] Identification stator resistance after restart / Rst_ident Restart
p0622[0...n] Motor excitation time for Rs_ident after switching on again / t_excit Rs_id
p0625[0...n] Motor ambient temperature during commissioning / Mot T_ambient
p0626[0...n] Motor overtemperature, stator core / Mot T_over core
p0627[0...n] Motor overtemperature, stator winding / Mot T_over stator
p0628[0...n] Motor overtemperature rotor / Mot T_over rotor
r0630[0...n] Mot_temp_mod ambient temperature / Mod T_ambient
r0631[0...n] Mot_temp_mod stator iron temperature / Mod T_stator
r0632[0...n] Mot_temp_mod stator winding temperature / Mod T_winding
r0633[0...n] Mot_temp_mod rotor temperature / Mod rotor temp
p0634[0...n] Q flux flux constant unsaturated / PSIQ KPSI UNSAT
p0635[0...n] Q flux quadrature axis current constant unsaturated / PSIQ KIQ UNSAT
p0636[0...n] Q flux direct axis current constant unsaturated / PSIQ KID UNSAT
p0637[0...n] Q flux flux gradient saturated / PSIQ Grad SAT
p0650[0...n] Actual motor operating hours / Mot t_oper act
p0651[0...n] Motor operating hours maintenance interval / Mot t_op maint

Table of Contents

Other manuals for Siemens SINAMICS G120

Related product manuals