Siemens SINAMICS G120 - Fig. 3-176 8060 - Fault buffer

3 Function diagrams 3.20 Diagnostics
SINAMICS G120 Control Units CU240B-2/CU240E-2
756 List Manual (LH11), 01/2016, A5E33839529
Fig. 3-176 8060 – Fault buffer
- 8060 -
Function diagram
87654321
fp_8060_97_51.vsd
Diagnostics
G120 CU240B/E-2
09.12.2015 V4.7.6
Fault buffer
III
1 ms
[2546.7]
p2103 ... p2105
[2546.7]
p2106
[2546.7]
p2107
[2546.7]
p2108, p3110 ... p3112
32 bit counter,
free running
[8065.1]
Operating time
This fault is overwritten when "more recent" faults occur.
The buffer parameters are cyclically updated in the background (refer to the status signal in r2139).
t_System relative
0 ... 4294967295 [ms]
p0969 (0)
r2138
r2138
.13
r2138
r2138.14
r2138
r2138.15
<1>
<2>
<1>
RESET
r0945 = 0
r0948 = 0
r0949 = 0
r2109 = 0
r2130 = 0
r2133 = 0
r2136 = 0
r3120 = 0
r3122 = 0
III
RESET
III
RESET
POWER ON
1
[2548.2]
r0949[63] [I32]
r2133[63] [Float]
r0945[0]
r0945[1]
r0945[7]
r0945[56]
r0945[57]
r0945[63]
r0945[8]
r0945[9]
r0945[15]
r0949[0] [I32]
r2133[0] [Float]
r0949[1] [I32]
r2133[1] [Float]
r0949[7] [I32]
r2133[7] [Float]
r0949[56] [I32]
r2133[56] [Float]
r0949[57] [I32]
r2133[57] [Float]
r0949[8] [I32]
r2133[8] [Float]
r0949[9] [I32]
r2133[9] [Float]
r0949[15] [I32]
r2133[15] [Float]
r0948[0] [ms]
r2130[0] [d]
r0948[1] [ms]
r2130[1] [d]
r0948[7] [ms]
r2130[7] [d]
r0948[56] [ms]
r2130[56] [d]
r0948[57] [ms]
r2130[57] [d]
r0948[63] [ms]
r2130[63] [d]
r0948[8] [ms]
r2130[8] [d]
r0948[9] [ms]
r2130[9] [d]
r0948[15] [ms]
r2130[15] [d]
r2109[0] [ms]
r2136[0] [d]
r2109[1] [ms]
r2136[1] [d]
r2109[7] [ms]
r2136[7] [d]
r2109[56] [ms]
r2136[56] [d]
r2109[57] [ms]
r2136[57] [d]
r2109[63] [ms]
r2136[63] [d]
r2109[8] [ms]
r2136[8] [d]
r2109[9] [ms]
r2136[9] [d]
r2109[15] [ms]
r2136[15] [d]
1
<2>
Fault times
Actual
fault case
Faults
Acknowledging
1. Acknow-
ledged
fault case
7. Acknow-
ledged
fault case
[oldest]
Fault
Fault
Fault
Fault code Fault value
Fault time
"received"
Fault time
"removed"
0 = "No fault present"
Fault case
appears
Delete fault buffer
Fault disappears
Fault appears
LED "RDY" [= red for fault]
Fault case
acknowl.
Counter
16 bit
p0952 = 0:
Fault buffer is deleted/
cleared
Automatic
16 bit counter,
free running
Fault buffer change [8065.6]
Fault responses to the sequence control
Fault cases qty
0 ... 65535
p0952 (0)
r0944
Fault buff change
ZSW fault/alarm 1
r2139
r2139
.3
3120[0]
3120[1]
3120[7]
3120[56]
3120[57]
3120[63]
3120[8]
3120[9]
3120[15]
r3122[0]
r3122[1]
r3122[7]
r3122[56]
r3122[57]
r3122[63]
r3122[8]
r3122[9]
r3122[15]
Diagnostic
attribute
fault
2
1
8
Fault
Fault
Fault
2
1
8
Fault
Fault
Fault
2
1
8
Component
fault
r2131
Act fault code
r3131
Act fault val
r3132
Comp_no act
POWER ON
Faults ackn DO
p3981
r2138.7
r2138
1 = Acknowledge fault
1 = External fault 1
(F07860) effective
1 = External fault 2
(F07861) effective
1 = External fault 3
(F07862) effective
1 = Fault present
1 = Fault gone/can be acknowledged
r2139.15