Siemens SINAMICS G120 - 2.4.4 Connector outputs (CO)

SINAMICS G120 Control Units CU240B-2/CU240E-2
List Manual (LH11), 01/2016, A5E33839529
545
2 Parameters
2.4 BICO parameters (connectors/binectors)
r20199 BO: DFR 0 output Q / DFR 0 output Q
r20200 BO: DFR 0 inverted output QN / DFR 0 inv outp QN
r20204 BO: DFR 1 output Q / DFR 1 output Q
r20205 BO: DFR 1 inverted output QN / DFR 1 inv outp QN
r20210 BO: BSW 0 output Q / BSW 0 output Q
r20215 BO: BSW 1 output Q / BSW 1 output Q
r20232 BO: LIM 0 input quantity at the upper limit QU / LIM 0 QU
r20233 BO: LIM 0 input quantity at the lower limit QL / LIM 0 QL
r20240 BO: LIM 1 input quantity at the upper limit QU / LIM 1 QU
r20241 BO: LIM 1 input quantity at the lower limit QL / LIM 1 QL
r20262 BO: INT 0 integrator at the upper limit QU / INT 0 QU
r20263 BO: INT 0 integrator at the lower limit QL / INT 0 QL
r20270 BO: LVM 0 input quantity above interval QU / LVM 0 X above QU
r20271 BO: LVM 0 input quantity within interval QM / LVM 0 X within QM
r20272 BO: LVM 0 input quantity below interval QL / LVM 0 X below QL
r20279 BO: LVM 1 input quantity above interval QU / LVM 1 X above QU
r20280 BO: LVM 1 input quantity within interval QM / LVM 1 X within QM
r20281 BO: LVM 1 input quantity below interval QL / LVM 1 X below QL
r20301 BO: NOT 4 inverted output / NOT 4 inv output
r20305 BO: NOT 5 inverted output / NOT 5 inv output
r20313 BO: NCM 0 output QU / NCM 0 output QU
r20314 BO: NCM 0 output QE / NCM 0 output QE
r20315 BO: NCM 0 output QL / NCM 0 output QL
r20319 BO: NCM 1 output QU / NCM 1 output QU
r20320 BO: NCM 1 output QE / NCM 1 output QE
r20321 BO: NCM 1 output QL / NCM 1 output QL
r20325 BO: RSR 2 output Q / RSR 2 output Q
r20326 BO: RSR 2 inverted output QN / RSR 2 inv outp QN
r20330 BO: DFR 2 output Q / DFR 2 output Q
r20331 BO: DFR 2 inverted output QN / DFR 2 inv outp QN
r20336 BO: PDE 2 output Q / PDE 2 output Q
r20341 BO: PDE 3 output Q / PDE 3 output Q
r20346 BO: PDF 2 output Q / PDF 2 output Q
r20351 BO: PDF 3 output Q / PDF 3 output Q
r20356 BO: MFP 2 output Q / MFP 2 output Q
r20361 BO: MFP 3 output Q / MFP 3 output Q
2.4.4 Connector outputs (CO)
Product: SINAMICS G120 CU240, Version: 4707900, Language: eng, Type: CO
r0021 CO: Actual speed smoothed / n_act smooth
r0025 CO: Output voltage smoothed / U_outp smooth
r0026 CO: DC link voltage smoothed / Vdc smooth
r0027 CO: Absolute actual current smoothed / I_act abs val smth
r0032 CO: Active power actual value smoothed / P_actv_act smth
r0034 CO: Motor utilization thermal / Mot_util therm
r0035 CO: Motor temperature / Mot temp
r0036 CO: Power unit overload I2t / PU overload I2t
r0037[0...19] CO: Power unit temperatures / PU temperatures
r0039[0...2] CO: Energy display / Energy displ
r0042[0...2] CO: Process energy display / Proc energy disp
r0060 CO: Speed setpoint before the setpoint filter / n_set before filt.
r0062 CO: Speed setpoint after the filter / n_set after filter
r0063[0...2] CO: Speed actual value / n_act